Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How Wide Is a Stackable Washer and Dryer? Check Before Buying

Prime for Young Adults: check your eligibility on Amazon

Many separate stackable washer and dryer pairs are about 24 or 27 inches wide. The exact width depends on the model, so those numbers are a starting point, not a promise that a set will fit.

A compact pair may take less wall space than a full-size pair, and the washer and dryer can differ slightly in width. You’ll also need to allow for any extra room the maker requires beside the machines. Before buying, measure the space and the narrowest point on the way in, then compare those measurements with the specific machines’ listed dimensions and clearance needs.

The Short Version

  • Compact and full-size stackable washer-dryer pairs often measure about 24 or 27 inches wide, but the exact size depends on the model.
  • For floor space, use the width of the wider machine in the pair. Leave any extra room the manufacturer requires beside it.
  • Measure the final spot and the whole route into it, including the narrowest doorway, hall, or turn.
  • Confirm the listed width and clearance needs for both machines before you buy. Don’t rely on a general size estimate.

What Sets the Width of a Stackable Pair?

A stackable pair takes up the floor space of one machine, not two side by side. The washer sits below the dryer, so the width to plan around is the width of the wider machine. If the washer is wider, use the washer’s measurement; if the dryer is wider, use the dryer’s.

Many separate compact pairs are about 24 inches wide, while many full-size pairs are about 27 inches wide. Those are useful estimates, not guarantees. A particular model may be wider or narrower, and the washer and dryer in a pair may not have matching measurements.

Check the width for the exact washer and dryer you plan to stack. If the manufacturer sells them as a matching pair, confirm that the listed dimensions apply to both pieces and that the dryer is approved to sit on that washer. A similar-looking machine is not automatically a match.

The listed machine width also may not tell you how wide the installation space should be. Side clearance means extra room beside the machine. The manufacturer may call for space at the sides for installation, airflow, or access, so a machine that measures 24 inches wide may need a wider opening to fit as intended.

Measure the Laundry Space and the Route

Measure the space where the machines will stand, then measure the route they must travel to get there. A set can fit in the closet but still be impossible to bring through the apartment doorway or around a tight hallway turn. Write each measurement down so you can compare it with the exact machine dimensions later.

  1. Find the narrowest point. Measure the opening where the machines will sit, then check each doorway, hall, and turn along the delivery route. Look for anything that sticks into the path, such as a door handle, trim, a railing, or a cabinet edge.
  2. Measure the usable opening. Measure between the surfaces that actually limit the machine’s path, not just the door panel. If the door can be removed, don’t assume that solves the problem until you know whether the frame or nearby wall is still narrower.
  3. Check turns and obstacles. A machine may fit through a doorway when facing straight ahead but not when it has to turn immediately into a short hall. Note the space available to pivot and check whether a door can open fully during delivery.
  4. Measure the final spot. Check the width between the walls or cabinets where the washer will stand. Measure at more than one height if the walls, trim, or nearby shelves change the opening.
  5. Compare the route with the machine’s full dimensions. Width alone does not settle whether a machine can pass through. Check its listed height and depth too, and ask the retailer or delivery service what dimensions they need for the route.

Measure from solid edge to solid edge, and keep the tape level. If a closet opening is wider at the bottom than near a shelf, use the tightest measurement. A small difference can matter when there is little room to angle or turn the machine.

Also check whether doors, trim, or other removable parts affect the opening. Don’t remove a door or alter a wall just to make a machine fit unless you have permission and know the change is safe. For a tight or complicated route, ask the delivery service or an installer to review your measurements before purchase.

Allow for Side Clearance and Other Installation Needs

The machine’s width is only part of the space to plan. Before buying, check these details in the installation instructions for the exact set:

  • Space beside the machines: Look for the required clearance at each side. Include that extra room when comparing the machine with a closet or cabinet opening.
  • Room behind the machines: Hoses and plugs need space behind the washer and dryer. The amount depends on the model and where its connections sit, so use the manufacturer’s instructions rather than pushing the machines tightly against the wall.
  • Space above the dryer: Check the listed height of both stacked machines and any required space above them. A low shelf or cabinet can block the installation even when the floor width works.
  • Room to open doors and reach controls: Make sure you can open the washer and dryer doors and reach the controls without hitting a wall, cabinet, or another appliance.
  • Stacking parts and support: Confirm that the machines are made to stack together and whether the manufacturer requires a specific stacking kit. Follow the instructions for a stable setup.

Don’t count a thin gap as useful clearance unless the manufacturer says it is enough. A machine wedged between walls can be difficult to install or move later, and may leave too little room for the connections or access the instructions require. If your measurements are close, ask the manufacturer or an installer to confirm the fit before you commit.

Where to Confirm the Exact Measurements

Use the manufacturer’s product page and installation instructions for the specific washer and dryer. Check the separate listings if the pair is sold as two machines. Look for the dimensions, usually shown as width, height, and depth, and make sure you are reading the machine size rather than the shipping box size.

  • Confirm both widths. Compare the washer and dryer measurements. Use the wider one to estimate the stack’s floor width.
  • Read the installation instructions. Find the required side, rear, and overhead clearances. These can differ by model and may not appear beside the main product description.
  • Check the stacking instructions. Make sure the dryer can be stacked on the exact washer and note any required parts or setup rules.
  • Ask about delivery access. If a doorway or turn is close to the machine’s measurements, give the delivery service the route dimensions and ask whether the machine can be brought through.

If the listing leaves out a measurement or the instructions are unclear, contact the manufacturer or seller before ordering. Don’t use a measurement from a different model in the same product line. A small change in the cabinet shape or attached parts can affect whether a tight opening works.

Will the Set Fit Through the Doorway?

Compare the narrowest opening on the route with the machine dimensions and the delivery service’s requirements. Don’t assume that turning the machine sideways will solve the problem. The depth or height may then become the limiting measurement, and a tight turn can leave no room to maneuver.

Ask whether the delivery team can remove the door from its hinges or take off any machine parts that the manufacturer permits. Confirm what the delivery service will do before purchase, especially in an apartment with a narrow entry or shared hallway. Don’t force a machine through an opening or attempt to lift and twist a heavy appliance without appropriate help.

If the machine cannot pass safely, pause the delivery plan. Contact the retailer, delivery service, or a qualified installer to discuss options. Avoid removing trim, doors, or cabinets without permission from the property owner and a clear plan for restoring them.

FAQs

How wide is a compact stackable washer and dryer?

Many compact pairs are about 24 inches wide, but the exact size varies by model. Check the listed width of both machines and include the side clearance required in the installation instructions.

Do I measure the washer, the dryer, or both?

Measure both, because the two machines may not have the same width. The wider machine sets the stack’s floor width, while the full set’s height and depth matter for the final space and delivery route.

How much extra room should I leave at the sides?

There isn’t one side gap that applies to every set. Find the required side clearance in the installation instructions for the exact model, then add that space to the machine width when checking the opening.

Where do I find the exact dimensions?

Check the manufacturer’s product page and installation instructions for the specific washer and dryer. Confirm the width, height, depth, stacking requirements, and clearances before ordering; ask the manufacturer or seller if any detail is missing.

Related guides: how wide is a washer and dryer and how wide are a washer and dryer.

5
1 ratings
Cody Rayburn
WRITTEN BY
Cody Rayburn
Cody is a home appliances editor based in Portland, Oregon. She specializes in eco-friendly and sustainable home appliances. With a decade of experience in the field, Cody is known for her comprehensive reviews and guides that focus on the environmental impact of appliances.