Why Your Samsung Washer Won't Drain and How to Fix It
Leave the washer door shut so gallons of dirty water do not spill across the floor. Most drainage problems happen when small items like coins or baby socks choke the cleanout trap, or when the drain hose gets pinched against the wall behind the machine. Draining that trapped water through the small front tube and pulling the debris free usually gets the drum spinning normally again right away.
The exact steps depend on your washer design and any warning message flashing on the display. Front-load models have a small access door near the floor for easy draining, while top-load designs empty directly through the rear pipe. Codes like 5C, 5E, or Nd confirm water cannot escape, while a low humming sound helps you tell if the pump wheel is simply jammed. Take these straightforward steps to empty the drum cleanly and clear the passage.
Why did my Samsung washer stop mid-cycle?
When a washer halts before the rinse or spin phase, the machine tried to pump out the water but could not lower the water level quickly enough. A water level pressure sensor monitors how much liquid remains in the stainless steel clothes tub. If that sensor detects standing water after ten to fifteen minutes of pumping, the electronic control board stops the cycle to prevent motor burnout or an indoor flood.
On digital displays, this problem shows up as a warning message on the display. Common drain codes include 5C, 5E, Nd, or E2, depending on the age of your appliance. Older Samsung units flash 5E or Nd (meaning No Drain), while newer models show 5C. These warning messages all mean water cannot escape the machine.
In most homes, the cause is a simple physical blockage inside the lower cleanout trap, a kinked drain hose behind the cabinet, or heavy soap foam choking the line. Using standard soap instead of low-suds HE (High Efficiency) detergent creates thick suds. This foam tricks the pressure sensor into reading water where none exists, or it creates an air pocket that stops the pump from moving liquid.
Your machine style also shapes how water drains and where clogs settle. Front-load units send water through an accessible lower front filter, while top-load machines rely on direct discharge lines routed out the back. When planning laundry spaces, exploring which is better, a top or front load washing machine helps explain how these internal layouts change everyday care.
How do I drain the water without a flood?
Before checking any internal components, you must empty the dirty water trapped in the drum. Never force open the door on a front-load washer while water sits against the glass. Doing so dumps several gallons of dirty water straight onto your laundry room floor.
Follow these steps to empty the drum safely:
- Disconnect the electrical supply. Unplug the power cord from the standard 120-volt 3-prong grounded wall outlet. Never touch internal components while the washer has power. If the load ran with hot water, wait thirty to forty minutes for the drum to cool so you do not burn your hands.
- Set up your work area. Lay several thick bath towels beneath the lower front panel of the washer. Keep a wide, shallow dish such as a baking pan or an oil drain tray handy, along with an empty five-gallon bucket.
- Open the cleanout access door. Find the small access door at the bottom corner on the front of the washer. Press the push latch or use a flat, cloth-wrapped tool to pop the panel open.
- Position the emergency drain tube. Beside the round filter knob, locate the small rubber tube clipped to the frame. Pull the flexible tube out gently. Place your shallow dish underneath the capped end.
- Drain the water in stages. Uncap the stopper over the dish. When the dish fills, recap the tube, pour the water into your bucket, and repeat. Continue until water stops flowing.
- Bail top-load models manually. Top-load washers lack a front cleanout door. Open the lid and scoop out standing water with a plastic bowl into a bucket. Then lower the rear drain hose flat near floor level into a shallow tray so gravity pulls out the final puddle.
How do I clean out the pump filter trap?
After draining the drum, you can safely remove the cleanout trap without flooding your floor. Coins, hairpins, and lint routinely escape pockets and collect in this small chamber.
Follow these steps to clear the filter assembly:
- Protect the floor. Even after draining through the tube, a small amount of water remains inside the housing. Keep a folded towel under the cap to catch any spills.
- Unscrew the cleanout trap cap. Turn the circular plastic knob counterclockwise. If debris jams the threads, the knob will feel stiff. Turn firmly and steadily until the cylindrical filter slides straight out.
- Clear caught objects. Check the plastic basket for trapped items. Coins, bobby pins, hair ties, baby socks, and dense lint balls frequently lodge here. Discard all debris into the trash.
- Scrub the filter screen. Wash the filter basket under warm running water in a utility sink. Use an old soft toothbrush to scrub away built-up soap scum and slime.
- Check the spinning pump wheel. Shine a flashlight into the empty chamber inside the washer. At the back, look for the small plastic fan known as the spinning pump wheel (impeller). Reach in carefully and turn the blades with your finger. The wheel should turn freely with distinct, springy magnetic resistance every quarter turn. If thread or a screw jams the blades, pry it out.
- Reinstall the cleanout trap. Slide the clean filter back into place, matching the guide rails. Turn the knob clockwise until it stops firmly. Push the rubber stopper back into the emergency tube, snap the tube into its clip, and close the access door.
Is the drain hose or wall pipe blocked?
If the cleanout trap was completely clear, the restriction is likely inside the rear drainage line. High-speed spinning causes washers to vibrate, which can push the appliance backward and pinch the hose.
Check these key points behind the machine:
- Hose kinks and wall clearance: Inspect the ribbed plastic discharge hose behind the washer. Confirm that the hose is not crushed against the baseboard or drywall. Leave 4 to 6 inches of clearance between the washer cabinet and the wall so the line bends smoothly.
- Insertion depth in the wall drain pipe: The discharge hose should extend only 6 to 8 inches into the wall drain pipe (standpipe). Pushing the hose too deep hits standing water in the plumbing P-trap or creates a siphon that draws dirty water back into the drum. Use the plastic U-bracket to secure the hose at the correct depth.
- Air gap at the standpipe: Water needs air behind it to flow smoothly. Never tape or seal the hose into the wall pipe. An airtight seal creates a vacuum lock that stops water from moving.
- Drain pipe height: The top of the wall drain pipe must sit between 39 and 96 inches from the floor. Below 39 inches, water siphons out while filling. Above 96 inches, the built-in drain pump cannot push water high enough.
- Plumbing flow capacity: Pull the washer hose from the wall pipe and pour a bucket of water directly into the drain pipe. If water spills over the rim, your household plumbing line is blocked, not the washing machine.
How do I know if the pump is broken?
When the cleanout trap and drain hoses are clear, the built-in drain pump motor may have failed. A pump assembly uses a small electric motor to spin the pump wheel inside a sealed housing.
Listen closely during the drain portion of a cycle to identify what is happening:
- A continuous buzzing or humming sound: The motor gets power, but the spinning pump wheel cannot turn. A small object like a toothpick or wire is jamming the blades, or the motor bearings have seized.
- Total silence from the bottom of the cabinet: The cycle reaches the drain phase, but the pump makes zero sound. The motor may be burned out, a wire harness has loosened from vibration, or the main control board failed to send power.
- Loud rattling or grinding noises: The motor spins, but the plastic pump wheel has sheared off its drive shaft or lost several blades. Without intact blades, the pump cannot create enough pressure to push water out.
Try an electronic reset before assuming the pump is dead. Unplug the power cable from the wall outlet for ten minutes. While the unit is unplugged, press and hold the power button for five seconds to drain stored power from the circuit board. Plug the washer back in, choose a spin-only setting, and listen for the pump to start.
Drain pump wear can also depend on machine style. Learning whether a front load or top load washing machine is better helps clarify how pump demands differ between vertical and horizontal wash systems over years of use.
When should I stop and call a professional?
Most drain clogs clear up once you empty the cleanout trap or straighten a pinched hose. Some symptoms point to electrical faults or mechanical issues that require a qualified repair professional.
Stop and disconnect power if you notice any of these warning signs:
- An electrical burning smell or smoke coming from beneath the washer.
- Water leaking from under the machine body rather than from external hose fittings.
- Repeated drain error messages that return even after clearing the trap, straightening the hose, and confirming the pump wheel spins freely.
- Melted plastic, frayed wires, or loose wire harnesses near the pump motor.
Replacing an internal pump involves tilting a heavy machine, removing body panels, and working around live wiring. If you are uncomfortable handling electrical parts or sharp sheet metal, an authorized appliance technician provides the safest solution.
FAQs
What does the 5C or 5E warning message on my Samsung washer mean?
A 5C or 5E code indicates that the washer tried to pump out water, but the water level failed to drop within a set time. Older models display 5E, while newer units show 5C. It almost always points to a blocked cleanout trap, a kinked discharge hose, or a jammed pump wheel.
Can using too much detergent cause my washer not to drain?
Yes, excess soap is a frequent cause of drainage stops. Overusing standard detergent creates dense suds that fool the pressure sensor and cause the pump to lose its prime through an airlock. Always use low-suds HE (High Efficiency) detergent and measure according to load size.
Why does my top-load Samsung washer leave clothes soaking wet?
If a top-load washer cannot drain completely, the inner wash basket cannot reach high spin speeds. This usually happens when an off-balance load pauses the spin cycle, or when small items and lint block the tub drain port beneath the bottom wash plate.
How often should I clean the lower cleanout trap on my washer?
Clean the cleanout trap once every one to two months under regular household use. If you frequently wash pet blankets, work gear, or clothes with heavy lint, inspect it once a month. Keeping the trap clear protects the pump wheel from sudden blockages.
Related guides: samsung washing machine wont start cycle and whirlpool washer wont spin and maytag washer wont drain.





















