How Do I Prepare and Drain a Washing Machine Before a Move?
Shut off the water, unplug the washer, and drain it before moving. Empty the supply hoses and remove as much leftover water as you can so it doesn’t spill in your home or vehicle. Keep a towel and a shallow container nearby for drips.
The exact steps depend on whether the washer is front-load, top-load, or portable, and whether it drains by gravity or uses a pump to push water out. Water can remain in the tub, hoses, or pump area, so check your manual for the right drain steps and any bolts needed to hold the drum still during the move. Start with the safe shutdown and drainage steps below.
Water can remain after the cycle ends
A washer can look empty and still hold water. A little may stay in the drain hose, the pump area, or a low spot in the tub. If the machine is tilted or lifted, that water can run onto the floor, into a moving vehicle, or across the new home.
The drain method depends on the washer. A built-in drain pump pushes water out, while a gravity drain hose lets water flow downhill and needs a suitable low drain. Some portable washers have two tubs, with a separate wash tub and spin basket, so water may remain in either one.
Check the washer’s manual before you begin. It shows where the drain hose, filter or drain plug are, if your model has them, and whether it needs special preparation for a move. If you cannot find the manual, look up the exact model on the maker’s website or contact the maker.
Shut off power and water before draining
Move clothes out of the washer. If a cycle is still running, use the washer’s cancel or stop control and wait for the door or lid to unlock. Don’t pull on a locked door or force the lid open.
Turn off the hot and cold water supply valves. They are usually on the wall behind the washer or under a nearby sink. Turn each handle clockwise until it stops, without forcing it. If you can’t find the valves or one will not turn, stop and ask a plumber or building manager for help.
Unplug the washer by holding the plug and pulling it from the wall outlet. Keep your hands dry. If water is already on or near the outlet, don’t touch the plug or step into the water. Keep others away and get help from a qualified electrician or emergency service as appropriate.
Give the washer a few minutes to stop and cool down if it has just been running. Put towels and a shallow container near the hoses before you disconnect anything. A small amount of water can spill even when the supply valves are closed.
Drain the washer and its hoses in order
Start with the method in your manual. Some washers have a drain or spin setting that runs the built-in drain pump. Others need the drain hose placed low so water can flow out by gravity. Don’t guess by tipping the machine; that can send water into places it normally does not go.
If the manual allows it, reconnect power only to run the washer’s drain or spin setting. Keep the floor and your hands dry, and make sure the drain hose is secured where the water is meant to go. Once the water stops flowing, stop the washer and unplug it again before handling hoses.
For a gravity-drain model, place the end of the drain hose over a floor drain or a container that can safely catch the water. Lower the hose only as the manual directs. Water may flow as soon as the hose end is low, so keep a steady grip and don’t leave it where it can slip or flood the floor.
Disconnect the drain hose from the wall drain or sink only after the washer is unplugged. Hold the hose over a bucket or shallow pan as you remove it. Keep the hose end raised until you are ready to empty it, then lower it into the container slowly.
Disconnect the hot and cold water supply hoses from the washer, using a towel and container to catch drips. Water may remain inside the hoses even after the valves are off. Keep track of which hose came from each connection if you will need to reconnect them later.
Check for water in the tub and remove it with a cup or absorbent towels if needed. If your manual describes a small drain hose or lower filter catch, follow those directions carefully and place a shallow pan underneath. Not every washer has a user-accessible drain or filter, so don’t pry off a panel or unscrew an unfamiliar part.
Catch water left in hoses and hidden areas
Drain hose: Hold both ends over a container while you empty it. Water can sit in a bend or low section, especially if the hose was routed along the floor.
Supply hoses: Keep a towel under each connection as you remove it. Drain the hoses into a sink or bucket, and store them so their open ends do not drip onto the washer or your belongings.
Tub and door area: Wipe the inside of the tub, the door opening, and the rubber seal around a front-load washer. Water can collect in folds of the seal. Leave the door or lid open while the washer dries, unless the manual says otherwise.
Pump area: A small amount of water may remain near the part that pushes water out. Use only the access point and method described in the manual. Open a drain plug or filter slowly over a shallow pan because water may come out suddenly.
Portable or twin-tub washers: Drain each tub as the manual directs. A separate spin basket does not necessarily drain the wash tub, and a machine with a built-in pump may need power to move water out before you unplug it for the move.
After draining, look underneath the washer and around the hoses for fresh drips. Wipe up any water before moving the machine. If water continues to leak from a connection or the washer’s body, don’t load it until you know where the leak is coming from.
Use the moving parts required for your model
Some front-load washers need transport bolts, which are bolts that hold the drum still during a move. They reduce movement of the drum while the washer is being carried or transported. If your model came with these bolts, check the manual for where they go and how to install them. Don’t assume every washer uses them, and don’t use bolts from another model.
Store any parts removed during installation, such as transport bolts or shipping supports, in a labeled bag with the manual. If the parts are missing, ask the manufacturer or moving company what the manual calls for before the washer is moved. A washer that needs drum supports should not be carried as if it were ready to move without them.
Also check the manual for instructions about the washer’s position during transport, securing the drum, and protecting the hoses or power cord. These directions vary by model. If the manual says the washer must stay upright, tell the movers before they begin and do not let them lay it on its side.
Pack and carry the washer without forcing it
Secure loose parts: Coil the drain and supply hoses without sharp bends. Tape or tie them to the washer only where the manual allows, and keep the power cord clear of the floor and moving equipment.
Close the door or lid: Follow the manual’s directions for keeping it shut during the move. Don’t tape over controls or pull the washer by its door, lid, hoses, or power cord.
Protect the route: Clear rugs, cords, and other objects from the path. Put towels or a waterproof layer under the washer if any dampness remains, but don’t use loose material that could make the machine slide.
Use enough help: Washers are heavy and awkward to grip. Use a suitable moving dolly and enough helpers for the machine and route. Don’t lift alone, drag the washer across the floor, or put fingers beneath it.
Keep it steady: Secure the washer upright in the vehicle if the manual requires that position. Keep it from shifting during travel, and don’t place heavy items on top of it.
At the new location, check the floor and the washer for leaks before reconnecting anything. Reinstall any parts the manual says to remove for use, reconnect the hoses to the correct connections, and turn the water valves on slowly. If a connection drips, turn the water off and correct it before running the washer. Follow the manual for leveling and the first cycle after the move.
Stop if the washer will not drain
If water remains, first check whether the washer is still plugged in only if the floor and outlet are completely dry and the manual calls for running a drain setting. Check that the drain hose is not kinked or pinched and that its end is placed as the manual directs. A blocked hose or an incorrectly placed hose can prevent water from leaving.
Don’t tip a full washer, force open a locked door, or remove panels to reach parts you do not recognize. If the washer makes an unusual sound, shows an error, keeps water in the tub, or leaks when you try the manual’s drain steps, unplug it if safe and keep the water supply off. Contact the manufacturer, a qualified appliance repair professional, or your building manager for help.
Related guides: how to drain a washer before moving it and how long does a washer machine last before replacement.





















