Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Do You Need to Remove Transit Bolts Before Using a New Washer?

Prime for Young Adults: check your eligibility on Amazon

As the first load starts, the new washer may shake or bang against the floor. Yes, remove the shipping bolts before using the washer, if the manufacturer supplied them to hold the drum still during delivery.

The bolts may be in different places, and some washers use another kind of shipping restraint. Check the manual to see what your model has, where to find it, and how to remove it safely. Follow its directions for any covers that came with the washer. Here’s how to check and what to do next.

Check the manual before touching any shipping parts

Transit bolts are shipping bolts that hold the washer drum still during delivery. The drum is the part inside the washer that holds your clothes. Keeping it still helps protect the washer while it is moved, but the bolts must be removed before normal washing if the manufacturer supplied them.

The manual is the safest way to tell what your washer uses and where those parts are. Some washers have bolts at the back. Others use a different shipping restraint, which may look or come out differently. Don’t assume that every large bolt, screw, plug, or panel on the washer is meant to be removed.

Leaving a shipping restraint in place can stop the drum from moving as it should. The washer may shake hard, bang, or shift during a spin. That can damage the washer or floor. Removing the wrong part can also cause trouble, so follow the instructions for your exact model rather than a general video or directions for a similar-looking washer.

Look for the restraints in the places named in your manual

Before you move the washer or reach behind it, switch it off. If it is plugged in, unplug it. Keep the washer level and ask someone to help if you need to move it; a washer is heavy, and pulling it by its hoses or power cord can damage them.

  • Read the setup pages. Look for terms such as “shipping bolts,” “transit bolts,” “shipping restraints,” or “transport bolts.” The manual should show their location and explain how they come out.
  • Check the pictured area. The manual may show bolts, spacers, clips, or other parts at the back or another part of the washer. Use its drawing to identify them. Do not remove a part just because it looks removable.
  • Compare the washer with the drawing. Look for the same number and arrangement of parts shown in the manual. If your washer’s back does not match the picture, check the model information on the washer and contact the manufacturer before proceeding.
  • Look for supplied covers. Some washers come with small covers that fit into the openings after the restraints are removed. The manual explains whether your model has them and where they go.

If you can’t find the manual, look for the model information on the washer and ask the manufacturer for the correct setup instructions. Don’t rely on a guess based on another washer’s appearance. A restraint can be easy to mistake for a part that should stay in place.

Remove the parts in the order your manual shows

Use the tools and steps listed for your model. Keep children and pets away while you work, and don’t put your fingers into openings or under a washer that could shift. If the instructions call for help moving the washer, get another adult rather than trying to tip or lift it alone.

  1. Make the washer safe to handle. Turn it off and unplug it. If the manual says to disconnect water hoses or move the washer for access, follow its directions and avoid pulling on the hoses. If a hose connection leaks or you can’t safely reach the back, stop and ask the manufacturer or a qualified appliance professional for help.
  2. Find each restraint shown in the manual. Match the parts to the drawing before loosening anything. Check the washer’s back and any other area the manual names. Don’t remove regular screws, panels, or parts that are not identified as shipping restraints.
  3. Loosen and remove the restraints as directed. Use the method and tool specified in the manual. Some models may have additional pieces that come out with a bolt. Keep the parts together as you remove them, and don’t force a part that won’t turn or slide out as described.
  4. Fit any supplied covers. If the manual says to cover the openings, press or fit the supplied covers into the correct places as shown. Don’t substitute random plugs or tape. If a cover is missing, ask the manufacturer what to do before using the washer.
  5. Check the washer before plugging it back in. Make sure the removed parts are accounted for, the covers are fitted if required, and the power cord and hoses are not trapped or damaged. Put the washer back in its intended position without pulling it by the cord or hoses.
  6. Follow the setup instructions for the first cycle. The manufacturer may give specific directions for getting the washer ready before laundry goes in. Use those directions, and don’t start a cycle if a restraint remains in place or you are unsure whether you removed the correct parts.

A part that resists removal is a reason to pause, not to apply more force. Stop if the bolt is stuck, a piece breaks, or the washer starts to tip. Check the manual again or contact the manufacturer with the model information.

Keep the removed bolts with the washer

Put the bolts and any related spacers or pieces in a labeled bag, then store the bag somewhere you can find it when the washer needs to move. A small label such as “washer shipping bolts” can save confusion later. Keep the manual with the bag if you have room.

The restraints may be needed again if the washer is moved to a new home or transported for service. Ask the manufacturer or the moving company how to prepare your model for transport. Don’t reinstall the parts unless the instructions say how, and don’t run a wash cycle with them installed.

Pause if the bolts are missing or the washer still shakes

  • You can’t find the bolts. Check the manual’s picture and confirm that it describes your exact washer. The washer may use another type of shipping restraint, or the parts may already have been removed. Ask the manufacturer to confirm what should be present before running a load.
  • The washer arrived without a manual. Find the model information on the washer and request the setup instructions from the manufacturer. Avoid removing parts based on a general guide, since the location and removal method vary.
  • You removed the restraints, but the washer bangs or shakes hard. Stop the cycle and switch off the washer. Check the setup instructions to confirm that every listed restraint was removed and that any required covers were fitted. Don’t keep running loads while the washer is moving violently.
  • The washer still moves after the restraints are accounted for. Check the manual for placement and leveling instructions. If a foot or other part of the washer is not resting as directed, the machine may rock on an uneven floor. Don’t put your hands under a running washer or try to steady it during a spin.
  • You hear loud banging, see a leak, or notice damage. Turn off the washer and unplug it if you can do so safely. If water is leaking near the plug or outlet, don’t touch the plug; keep clear and get qualified help. Contact the manufacturer or an appliance professional before using the washer again.
  • You are unsure whether a part is a restraint. Leave it in place and ask the manufacturer to identify it. Removing an unknown part can be as risky as leaving a shipping restraint installed.

A little movement during a cycle can have more than one cause, but hard shaking or repeated banging deserves attention. First confirm that the shipping parts were removed as instructed. If they were, follow the washer’s setup directions and get help if the noise or movement continues.

FAQs

How can I tell if my washer has transit bolts?

Check the setup section of the manual for a drawing and a list of shipping parts. Compare that drawing with the washer before removing anything. If the manual is missing or the parts do not match, ask the manufacturer to identify the restraint for your model.

Where should I look for shipping bolts?

Look only in the places shown in your washer’s manual. The bolts are often shown on the back, but the location varies, and some washers use a different shipping restraint. Don’t remove a screw or panel unless the manual identifies it as part of the shipping setup.

Can I run a load if I can’t find the bolts?

Don’t start a load until you know whether your washer has shipping restraints and whether they are already removed. Check the manual or ask the manufacturer using the washer’s model information. This is safer than guessing and risking hard shaking or damage.

What should I do if the washer still shakes after removal?

Stop the cycle and confirm that all listed restraints were removed and any required covers were fitted. Then check the manual’s placement and leveling directions. If the washer still shakes hard, bangs, leaks, or appears damaged, leave it off and contact the manufacturer or an appliance professional.

Related guides: how to remove rusted bolts from washer tub assembly and how to clean washer before first use.

4.5
2 ratings
Elvin Elliston
WRITTEN BY
Elvin Elliston
Elvin Elliston - Elvin is a home appliances expert who specializes in smart home integration. Based in Silicon Valley, California, Michael has been in the field for over 15 years, providing insightful reviews on the latest smart home appliances.