Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

What Should I Do If My Washing Machine Shows an Error Code?

Prime for Young Adults: check your eligibility on Amazon

Look up the exact code before resetting the washer. Codes vary by make and model, so check the washer’s manual or the manufacturer’s support page and follow the steps for your machine. Guessing can leave water in the drum or make a leak worse.

The right next step depends on the exact code and whether the washer is leaking, full of water, or showing another warning sign. Pause the cycle and look for danger first. Stop using the washer if you notice a leak, burning smell, unusual heat, or an electrical concern. A load gathered on one side or a blocked tube that carries used water away may be simple to fix, but only follow checks the manual allows. Start by finding the code and checking the washer safely.

Error codes point to a model-specific problem

A washing machine error code is a clue, not a universal diagnosis. The same letters or numbers can mean different things on different washers, so a code list for another brand or model may send you toward the wrong fix.

The code may point to a condition the washer noticed, such as water not draining, a door or lid not closing, or a load that cannot spin evenly. It does not always mean a part has failed. A small issue, such as clothing bunched on one side, can sometimes stop a cycle and bring up a warning.

Your washer’s make and exact model determine what the code means and which steps are safe. Find the model information on the washer’s label or in the paperwork that came with it. If you cannot find the model, check the manufacturer’s support page for guidance on locating the label.

The manual and support page have the right code list

Use the information for your exact washer, not a code list that only matches the brand. Manuals often have a troubleshooting section or an index where you can look up the code. The manufacturer’s support page may also let you search by model or enter the code.

Before following a suggested fix, make sure the model shown in the manual or support page matches the label on your washer. Similar-looking washers can use different controls and code meanings. If the code is flashing, note its letters and numbers in the order shown.

  • Write down the full code. Include any letters, numbers, or lights that appear with it. A partial code can point to the wrong instruction.
  • Check what the washer was doing. Note whether the code appeared while filling, washing, draining, or spinning. This detail can help you find the right entry in the manual.
  • Read the full instruction. Some manuals ask you to check a hose or redistribute clothes; others say to contact service. Do not assume that a step from a different model applies.
  • Keep the manual’s limits. If it says not to open a panel or repeat a cycle, follow that direction. Do not take the washer apart to investigate a code.

Pause first and look for immediate hazards

If you see water spreading across the floor, smell something burning, feel unusual heat, or suspect an electrical problem, stop using the washer. Do not touch a wet plug, cord, or outlet. If you can reach the washer’s controls without stepping in water or touching a hazard, turn it off. Otherwise, keep clear and get help.

When there is no sign of danger, pause the cycle before checking anything. A washer may have water inside or a load caught in the middle of a spin, so avoid pulling hard on the door or lid. Some washers keep the lid or door locked until it is safe to open.

  1. Pause or turn off the washer. Use the control named in the manual. Do not force the door or lid open if it stays locked.
  2. Record the code. Take a photo or write down the display before it disappears. Include any message or warning light shown at the same time.
  3. Look around the washer. Check the floor, the visible hoses, and the area around the outlet for water or damage. Do not move the washer if doing so could pull on a hose or cord.
  4. Check the manual’s instructions. Follow only the checks listed for your exact model and code. If the manual says to call for service, stop there.

If the washer has stopped with water inside, do not guess at a drain or door-release procedure. Check the manual for that code and for instructions on removing water. If those steps are unclear, or the water will not drain, contact the manufacturer or a qualified repair service before trying to open the machine.

Try only the simple checks your manual allows

Some codes can follow a condition you can correct without opening the washer. The manual may tell you to rearrange clothes, check that a door is fully closed, or look for a kink in the drain hose, the tube that carries used water away. Only try a check that the instructions allow, and keep your hands away from moving parts.

  • Look for a lopsided load. If the washer stopped during spinning, clothes may have gathered on one side of the drum. An unbalanced load means the clothes are bunched together instead of spread around the drum. If the manual allows it and the door or lid opens normally, spread the clothes evenly and remove a bulky item if the load is crowded.
  • Check the visible drain hose. If the code points to draining, look for a sharp bend, a crushed section, or something clearly blocking the hose’s path. Do not pull the washer out alone or disconnect a hose while it contains water. Follow the manual’s instructions for any adjustment.
  • Check the door or lid. Make sure clothing is not caught between the door or lid and its opening. Close it gently as the manual directs. Do not push, pry, or hold a lock in place.
  • Check the water supply only if directed. Some code instructions may ask you to confirm that the water shutoff valves are open or that a visible supply hose is not pinched. If you see a leak, stop instead of adjusting the connection.
  • Use the right amount of detergent. If the manual links the warning to excess suds, follow its detergent guidance. Too much soap can leave foam in the washer and interfere with draining. Do not add more detergent to try to clear a code.

Do not remove a lower filter, open a service panel, or reach into standing water unless the exact manual gives clear instructions and says it is safe. A filter can release water when opened, and some parts may be hot or powered. If the manual’s directions do not make the step clear, ask the manufacturer or a repair professional first.

Reset only when the manual says how

A reset means turning the washer off and back on as the manual directs. It may clear a temporary warning, but it does not repair a clogged hose, a leak, or a faulty part. Reset methods vary, so do not use a button combination or unplugging routine from another washer’s instructions.

Before resetting, make sure there is no leak, burning smell, unusual heat, or electrical concern. Read the code instructions first, because the washer may need to drain or remain off until it can be serviced. If the manual allows a reset, follow its exact steps and wait for the washer to finish the process before starting another cycle.

If the same code returns, do not keep resetting the machine or restarting the same load. Repeated attempts can leave more water in the washer or make a problem harder to manage. Note when the code returns and what the washer was doing, then contact the manufacturer or a qualified repair service.

Restart only after the cause is addressed

Before starting another load, check that the code has cleared and that the washer shows no signs of leaking or damage. Confirm that any simple correction you made matches the manual’s instructions. If you moved clothes around, make sure they are spread out rather than bunched on one side.

Use the washer’s normal controls to choose the next step the manual recommends. Do not run a full load just to see whether a warning comes back if the manual tells you to stop or contact service. If the manual permits a restart, stay nearby at first and watch for water on the floor, unusual sounds, or the same code.

If the washer completes the allowed cycle without the warning and no new problem appears, the issue may have been a temporary condition. That does not prove a recurring code is fixed. If it comes back during the next load, stop and seek service rather than repeatedly trying the same reset.

Some manuals recommend a cleaning cycle after certain issues. Use that cycle only if the manual says it applies to your code or situation. If the washer is working normally and you want general guidance on tub care, see this guide to washer drum cleaners, but cleaning products are not a substitute for repairing a fault.

Stop using the washer when danger signs appear

Stop and contact a qualified repair service if the washer leaks, gives off a burning smell, feels unusually hot, or shows signs of an electrical problem. Do not keep running it to see whether the warning goes away. If water is near a plug or outlet, stay clear and get help rather than touching the connection.

Call for service if the code remains after the manual’s permitted checks, returns after an allowed reset, or tells you to arrange a repair. A repair professional can use the code and the washer’s symptoms to decide what needs attention. Share the exact code, the model, when it appeared, and whether water remains in the drum.

Do not open the washer’s cabinet or try to repair wiring, locks, pumps, or other parts yourself. The machine may contain water, and internal parts can pose electrical or injury risks. If the manual does not describe a step as a user check, leave it to a qualified professional.

If the display goes blank, the code changes, or you cannot find a matching entry for your model, contact the manufacturer’s support team. Tell them what the washer was doing when the code appeared and what you observed around the machine. That is safer and more useful than guessing from a code list meant for another model.

4.7
3 ratings
Robert Durden
WRITTEN BY
Robert Durden
Hi there, I'm Robert! I love diving into the world of home appliances, and I've been doing it for 15 years from my home base in Atlanta. With a Marketing degree from Georgia State, I'm your go-to guy for hands-on reviews and comprehensive buying guides.