Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

What Is a Standard Size Washer and Dryer? Typical Dimensions

Prime for Young Adults: check your eligibility on Amazon

A standard pair is about 27 inches wide per machine. Each washer and dryer is usually about 30 to 34 inches deep, but height varies by style and model. Treat these as a starting point, not a promise that every pair will fit.

The space you need depends on whether the machines sit side by side or one above the other, and whether the washer opens from the top or front. Doors, hoses, and room for airflow also take space, while a narrow doorway or hallway can block delivery even when the laundry area seems large enough. Measure the room and the path in, then compare those measurements with the maker’s listed dimensions and setup directions.

The Short Version

  • A typical full-size washer and dryer are each about 27 inches wide and 30 to 34 inches deep, but the exact measurements depend on the model and style.
  • Side-by-side machines need room for both widths, while a stacked pair uses less floor width but needs enough height and must be approved for stacking.
  • Leave room for doors to open, hoses to bend, and air to move. A top-load washer also needs space above it for the lid.
  • Measure the laundry space and the full delivery path, then compare those measurements with the maker’s listed dimensions and setup directions.

How Side-by-Side and Stacked Machines Change the Space

With a side-by-side pair, the washer and dryer sit next to each other. Plan for the width of both machines together, plus any space the maker calls for at the sides. A narrow closet may fit the machines but leave little room to open the doors or reach the controls.

A stacked pair takes up the width of one machine on the floor. It needs more vertical room, and the washer and dryer must be made for stacking together. Don’t assume that two machines from the same brand can be stacked, or that any dryer can sit safely on any washer. Check the maker’s instructions and whether a specific stacking kit is required.

Stacking can help in a small laundry area, but it changes how you use the machines. The upper controls may be harder to reach, and the dryer door may open in a direction that blocks a wall or doorway. Check door direction and access before deciding that a stack is the better fit.

Front-load machines generally have doors that swing outward, so the open door needs room in front of the machine. A top-load washer needs room above its lid to open fully. If a shelf or cabinet sits overhead, make sure the lid can lift without hitting it and that you can reach inside comfortably.

Extra Room for Doors, Hoses, and Airflow

The machine’s listed depth is not always the full depth you need. Hoses and other connections sit behind the washer, and the back of the machine may need extra space from the wall. A planning allowance of 4 to 6 inches behind the machines can help account for hoses, but the exact space depends on the model and its setup directions.

  • Check the doors. Open each machine door as far as you expect to use it. Make sure it doesn’t hit a wall, hamper, cabinet, or the other machine. For a top-load washer, check the lid’s full path overhead.
  • Allow room for hoses. Look at where the water hoses and drain hose connect. Don’t force a machine tight against the wall if that bends, pinches, or traps a hose.
  • Leave the required open space. Follow the maker’s directions for spacing around the machines. Air needs to move as the machines run, and the directions may call for space at the back, sides, or top.
  • Check the door and handle depth. A listed measurement may not include every part that sticks out. Confirm whether the depth includes the door, knobs, or handles, especially if the machine sits in a narrow closet.

Closet doors can create a separate problem. They may close against the machines, block an open washer door, or limit airflow. Check the setup directions for any rules about closet doors and ventilation rather than assuming that a closed closet is suitable.

Measure the Laundry Area and Delivery Path

Use a tape measure and write down each result. Measure the clear opening, not just the wall space, and account for trim, pipes, shelves, and other things that stick out. These steps can help catch a fit problem before the machines arrive.

  1. Measure the laundry space. Record the usable width, depth, and height. Measure at more than one point if walls, cabinets, or floors are uneven. Use the smallest usable measurement when checking fit.
  2. Measure the floor space and hookups. Note where the water valves, drain, and electrical outlet are. Check whether a hose connection or outlet sticks out far enough to affect the machine’s position.
  3. Check the opening and door swing. Measure the closet or room opening with the door in the position it will be during delivery and use. Also check whether an open machine door would block the room entrance.
  4. Measure the route into the home. Check exterior and interior doors, hallways, stairs, and tight turns between the delivery entrance and laundry area. Measure narrow spots between trim or railings, not just the wider part of a hallway.
  5. Look for obstacles along the route. Note low ceilings, light fixtures, handrails, sharp corners, and steps. A machine can fit in the laundry area and still be too difficult to move through a tight turn.

Don’t rely only on the width of the doorway. The delivery path may require the machine to turn on its side or pass through a narrow hall, and the available space can change at each turn. Ask the delivery service or a qualified installer what measurements they need if the route looks tight.

Before delivery, clear the route and remove loose items that could catch on the machine. If a doorway must be altered or a machine needs to be moved in a way the maker does not allow, stop and ask a qualified professional. Avoid forcing a heavy machine through a space where it could damage a wall, hose, or person.

Confirm That a Specific Model Will Fit

Once you have the room measurements, compare them with the exact model’s listed dimensions. Don’t use a general size as a guarantee. Two machines with similar descriptions can differ in depth, height, door swing, or the room they need around them.

  • Check the complete dimensions. Find the listed width, depth, and height on the product page or maker’s information. Confirm whether those measurements include doors, handles, and other parts that extend outward.
  • Read the setup directions. Look for the maker’s required extra room around the machine, including behind it and above it. These directions explain the space the model needs once hoses are attached and doors are open.
  • Confirm the arrangement. For a side-by-side pair, check the combined width and each machine’s door swing. For a stack, confirm that the exact washer and dryer can be stacked and follow the instructions for any required kit.
  • Check the closet conditions. Look for directions about airflow and closet doors. Confirm that shelves, counters, and cabinets won’t block a top-load lid or leave too little room above a stacked pair.
  • Compare the delivery route. Check the machine’s full dimensions against every narrow doorway and turn. Ask the seller or delivery service to confirm any uncertain point before scheduling delivery.

If the machine’s listed depth fits only when pushed tight against the wall, pause and check the setup directions. The same goes for a top-load lid that barely clears a shelf or a front-load door that cannot open far enough for loading. A close fit on paper can become a daily nuisance once you need to reach the controls, move laundry, or clean behind the machine.

After you know the pair fits, you can compare other ownership questions separately. For example, this guide to what to look for in a reliable washing machine may help with your next decision, but it doesn’t replace checking the exact model’s dimensions.

FAQs

Do washer and dryer dimensions include the hoses?

Not always. Listed dimensions may describe the machine itself, while hoses add space behind it. Check the model’s setup directions and allow the required room for connections.

Does a top-load washer need more room than a front-load washer?

It may need more open space above it because the lid lifts upward. A front-load machine needs room in front for its door to swing open. Check the full opening path for the style you choose.

Can I stack a standard washer and dryer?

Only if the maker says that exact pair is suitable for stacking. Check the setup directions for the required stacking kit and height, and don’t place a dryer on a washer based on appearance alone.

What if the room fits the machines but the doorway does not?

Measure the entire route, including turns and narrow spots, before arranging delivery. Ask the delivery service or a qualified installer whether the machines can be moved through safely. Don’t force a machine through a tight opening.

Related guides: what is a good size washer and what is the standard size of a washing machine and what are the dimensions of standard washer and dryer.

4
3 ratings
Jessie Greene
WRITTEN BY
Jessie Greene
My name is Jessie Greene, a male home appliance expert from Los Angeles specializing in the luxury sector. For the past 12 years, I've been guiding consumers through the intricate world of high-end appliances.