Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Washing Machine Habits That Waste Water and Raise Your Bill

Prime for Young Adults: check your eligibility on Amazon

A utility statement arrives in the mail showing a sudden spike in the water charges, even though daily routines seem completely normal. In most laundry rooms, quiet water waste comes down to washing half-empty baskets, pouring too much soap, and running deep-fill cycles for ordinary clothes. Those extra gallons add up fast when a machine runs every few days.

The exact amount of waste depends on your washer style and the toggles you leave turned on. Older machines with manual dials fill the entire tub regardless of load size, while modern high-efficiency units use automatic weight sensors that trigger surprise rinse cycles when thick soap suds build up. Small extras like a pre-soak or an extra rinse also run up the meter when left on by mistake. Learning how to catch these habits helps you trim the bill while keeping laundry fresh.

Stop running half-empty loads throughout the week

Washing two shirts, a pair of jeans, and some gym shorts might feel like a quick way to stay on top of the laundry pile. But running partial loads is one of the fastest ways to run up your water bill. Whether you wash three items or twenty, a washing machine requires a baseline volume of water just to wet the drum, submerge internal sensors, and fill the plumbing lines.

In older top-load washers, the machine often fills with 30 to 40 gallons of water regardless of how few clothes are inside. Modern machines feature an automatic water weight sensor (load sensing) that adjusts water levels to the size of the load. Even with this feature, two small loads use substantially more water than a single full load. Each cycle requires its own separate wash fill, rinse fill, and drainage cycle.

Small loads also clean less effectively. Clothes clean themselves largely through friction, rubbing against other fabrics to work out body oils and dirt. In a half-empty wash tub, garments float loosely without enough contact to scrub stains away. When clothes do not come clean the first time, people frequently run them through the machine a second time, doubling the water and electricity consumed.

Turn off the deep water setting for normal laundry

Many modern top-load machines come with a button labeled deep fill or deep water wash. This extra water setting tells the machine to ignore its automatic sensors and flood the tub with several extra gallons of water. Many people turn this on for every cycle because they look through the glass lid and worry that the laundry looks too dry.

Modern high-efficiency washers are specifically engineered to clean clothes using very little standing water. In top loaders equipped with a flat bottom wash plate (impeller) that moves laundry using water currents, clothes roll through a concentrated stream of water and soap. When reviewing the difference between agitator and impeller washers, you can see that impeller designs do not need clothes to be completely submerged to achieve a thorough clean.

Defaulting to deep fill wastes roughly 10 to 15 gallons of water per load. The extra water dilutes your laundry detergent, reducing its chemical power. It also cushions the garments so they do not rub against each other, which leaves fabrics dingy. When comparing front-load and top-load washers, front loaders do not even include a deep fill button because gravity tumbles clothes through shallow water, proving that full submersion is unnecessary.

Reserve deep water settings strictly for bulky bedding, thick comforters, or sports uniforms caked in heavy mud. For ordinary t-shirts, sheets, and office clothes, let the washer's normal cycle determine the water level automatically.

Cut back your detergent to stop accidental rinse cycles

Pouring too much laundry soap into your machine is a hidden cause of high water bills. Most detergent measuring caps are designed to encourage overuse, with faint lines that prompt users to fill the cup to the brim. In reality, a standard load of laundry only requires one to two tablespoons of concentrated soap.

When you pour excess soap into the dispenser, it creates a thick blanket of bubbles inside the stainless steel clothes tub. This causes a condition known as suds-lock (excess soap bubbles trapping the drum), which prevents water from draining properly and puts heavy strain on the drive motor. Modern washers use electronic sensors and water pressure switches to check whether water is draining smoothly from the machine.

If the computer detects thick foam lingering during the drain cycle, it automatically initiates a suds-recovery routine. The washer halts its normal cycle, opens the water valves, and pumps in several gallons of fresh cold water to knock down the suds. It agitates the load, drains the water, and checks for foam again. If suds remain, the machine can repeat this rinse-and-drain process up to four times in a single cycle.

This suds-clearing routine happens quietly in the background without triggering an error code on the display screen. You simply end up with a wash cycle that runs 20 minutes longer and burns through 10 to 20 extra gallons of clean water. Always use low-suds HE (High Efficiency) detergent in modern washers, and measure it carefully with a standard tablespoon instead of estimating with the cap.

Turn off automatic extra rinse and pre-soak buttons

Modern washing machines remember your previous cycle selections. If you enabled the extra rinse or pre-soak feature for a load of muddy towels three weeks ago, your washer may keep those buttons illuminated for every future wash cycle until you manually shut them off.

An extra rinse is not a thirty-second spray of water. On standard washers, an extra rinse is an entire secondary cycle where the machine fills the inner wash basket to capacity, agitates the load, drains the water, and spins the tub dry. That single setting adds 10 to 18 gallons of water to every cycle. Running twenty loads a month with extra rinse turned on can waste over 300 gallons of water.

Pre-soak settings cause similar waste. When pre-soak is engaged, the machine fills the tub, lets the garments sit in water for 15 to 30 minutes, and then pumps that entire tub of water directly down the drain pipe before refilling the tub from scratch for the actual wash cycle. You end up paying for two complete tub fills before your clothes are even washed.

You only need an extra rinse if someone in your home has a diagnosed skin allergy, severe eczema, or sensitivity to laundry scents, or if you are cleaning reusable cloth diapers. For standard soil, one rinse cycle clears away all soap residue. If a specific garment has a stubborn stain, pretreat it in a sink basin rather than making your washer fill and drain an entire tub for a pre-soak.

Check your fill hoses and water intake valves for silent leaks

Not all water waste comes from cycle selection or laundry habits. Small mechanical failures behind the machine can quietly waste hundreds of gallons of water every month without leaving a puddle on your laundry room floor.

The water intake valve behind the machine (inlet valve) controls household water flowing into the tub. This valve uses internal electrical solenoids and rubber seals to open and close. Over time, sediment from household plumbing, hard water scale, or worn internal springs can prevent the valve from seating shut completely. When this happens, water slowly seeps into your washer around the clock.

To inspect your machine for a slow valve leak, follow these quick checks:

  • Inspect the wash tub in the morning: Leave the washer empty overnight with the lid closed. Open the machine in the morning before running any laundry. If the bottom of the stainless steel clothes tub is wet or has standing water, the water intake valve is weeping and needs to be replaced.
  • Feel the water supply lines: Reach behind the machine to check the hot and cold water supply hoses. Make sure the connections at the wall water shutoff valves and the back of the washer are dry and free of green corrosion or white mineral buildup.
  • Examine the drain hose depth: Make sure your drain hose is not pushed too far down the wall standpipe. If the hose extends more than 6 to 8 inches into the pipe, it can create a siphon that pulls water out of the drum while the washer fills, forcing the machine to keep running fresh water into the tub continuously.

Follow these daily habits to keep your water bill down

Forming efficient laundry habits takes only a few minor adjustments to how you load clothes and set your dials. Use this daily routine to keep your washer running efficiently:

  1. Build balanced, full loads: Wait until you have enough dirty laundry to fill the inner wash basket about three-quarters full without pressing clothes down. For top loaders with a center agitator post that twists clothes through the water, place garments evenly around the post so the tub stays balanced during high-speed spinning.
  2. Stick to the Normal or Eco cycle: Avoid specialized cycles like Heavy Duty or Bulky unless you are washing heavy blankets or work wear. Normal cycles make full use of the machine's automatic water weight sensor to dispense the precise amount of water needed for the weight of your fabrics.
  3. Measure your detergent accurately: Use one tablespoon of low-suds HE detergent for light or normal loads, and two tablespoons for large, heavily soiled loads. Pour it into the dispenser drawer rather than pouring it loosely over the dry clothes.
  4. Deselect cycle modifiers: Check the control panel before pushing the start button. Make sure specialty options like deep fill, pre-soak, and extra rinse are switched off.
  5. Wash with cold water: Modern laundry detergents use specialized enzymes that dissolve and activate in cold water. Cold water cuts down your electric or gas water heater usage without requiring any extra rinse cycles.
  6. Leave the washer door open between loads: Keep the lid or door cracked open an inch or two when the machine is idle. Allowing air to circulate inside prevents sour mildew odors from taking hold, saving you from running empty cleaning cycles with hot water just to freshen the tub.

FAQs

Which washer setting uses the most water?

The heavy-duty cycle paired with the deep fill and extra rinse settings consumes the most water of any combination. Heavy-duty cycles use higher baseline water volumes to cushion stiff fabrics, while deep fill overrides sensors to flood the drum to its maximum limit. Adding an extra rinse to that cycle forces the machine to fill and drain a second high-volume tub of water, which can easily exceed 40 gallons in a single run.

Does washing several small loads use more water than one big load?

Yes, washing multiple small loads uses substantially more water than running one full load. Every wash cycle requires a minimum baseline volume of water to wet the inner basket, prime the pump, and fill the plumbing lines, regardless of load size. Running two half-empty loads forces the washer to fill and drain that baseline volume twice, doubling your water consumption for the exact same amount of clean clothes.

Can using too much laundry detergent actually make the machine add extra water?

Yes, excessive detergent creates thick suds that modern high-efficiency washers detect during the drain portion of the cycle. When sensors spot excess foam, the machine enters an automatic suds-recovery routine that adds extra gallons of cold water to dilute and flush out the bubbles. This automatic routine can repeat multiple times per load, adding up to 20 gallons of wasted water to your utility bill without displaying any alert on the screen.

How do I know if my washer is filling with more water than it really needs?

In a modern high-efficiency washer, clothes should be saturated and tumbling through a shallow pool of water near the bottom of the drum. If your clothes are floating freely with several inches of standing water visible above them, your machine is using far more water than necessary. This usually indicates that the deep fill setting is accidentally turned on, or that hard water scale is clogging the pressure sensor that measures tub water levels.

4.3
3 ratings
James Patterson
WRITTEN BY
James Patterson
Hi, I'm James, a home appliance nerd hailing from New York City. Armed with my trusty Electrical Engineering degree from MIT and 10 years of experience, I've been helping people navigate the wild world of smart home tech.