How to Clean a Washing Machine and Stop Odors
A load of freshly washed laundry comes out of the drum smelling like sour mildew instead of clean cotton. Getting rid of that funk requires running an empty hot cycle with liquid bleach or a washing machine tablet, then wiping away the trapped sludge. That heat and cleaner combination kills bacteria and dissolves dried detergent hiding behind the metal tub.
The exact routine depends on your machine setup and the kind of buildup inside. Front-loaders trap standing water and black slime in the flexible rubber door seal, while top-loaders collect greasy soap scum underneath the top rim. White mineral scale from hard water calls for a separate vinegar wash, while sour mold needs sanitizing bleach. Many front-loading models also have a small drain filter near the floor that needs emptying. The steps below show you how to clean each part safely without damaging your machine.
Why Washing Machines Develop Foul Odors and Soap Scum
Most people assume a washing machine cleans itself every time laundry runs through it. In reality, modern washing machines trap dirt, body oils, and detergent residue in areas you cannot easily see. Over time, that buildup turns into a greasy, gray sludge called soap scum (dried detergent and softener sludge). When dampness sits inside a closed washer between cycles, bacteria and mildew feed on this sludge, creating that sour, mildew smell that clings to your clean towels and clothes.
A big reason this buildup happens is how we wash clothes today. Decades ago, most households washed clothes in hot water using powdered soap. Today, most laundry cycles run in tap-cold water to save energy and protect delicate fabrics. Cold water is great for preserving colors, but it does not dissolve body grease, pet dander, or detergent binders very well. These oily residues stick to the outer side of the stainless steel clothes tub and coat the drainage pipes.
The type of soap you use also plays a massive role. Liquid fabric softeners are made with oil-based ingredients and animal fats designed to coat fabric fibers. When washed into your machine, those same fats coat the plastic drum basin and drain lines. Using regular laundry detergent instead of low-suds HE (High Efficiency) detergent creates a similar issue. Regular soap generates excessive foam that modern, water-saving machines cannot fully rinse away. That leftover foam settles inside the tub and dries into a sticky film.
Your washer design influences where this gunk hides. Front-load washers use an airtight door with a thick rubber seal to prevent water leaks. That seal holds onto moisture after every load, creating an ideal dark, humid environment for mold. Top-load washers circulate air better through the loose lid, but they collect lint, pet hair, and softened scum underneath the top plastic tub rim and along the center agitator post. Understanding whether front-load or top-load washing machines fit your laundry routine can help you anticipate where moisture and grime build up over time.
How to Deep Clean the Wash Drum and Tub Safely
Deep cleaning the drum requires hot water and a cleaner strong enough to dissolve stubborn sludge. You do not need expensive specialty gear, but you do need patience to let the cleaning solution break down the film on the hidden side of the wash basket. Plan to run this cycle when you have an hour or two without laundry to do.
- Empty the washer completely: Check the stainless steel clothes tub thoroughly. Remove stray socks, washcloths, or pet blankets. Make sure no clothing is left stuck against the back wall or top rim.
- Add your chosen cleaner: You have two strong choices here. You can use an oxygen-based washing machine cleaning tablet, or you can use standard liquid chlorine bleach. If using a cleaning tablet, drop it directly into the bottom of the empty wash tub. If using liquid chlorine bleach, pour one cup (or the maximum fill line amount) directly into the main wash compartment of the soap drawer. Bleach is the best choice if you already see black mold or smell strong mildew. Tablets work best for breaking down thick mineral deposits and dried detergent.
- Select the hottest and longest cycle: Look at your machine control dial. If your washer has a dedicated "Tub Clean" or "Sanitize" setting, select that cycle. Those settings use the highest water temperature the machine can produce and soak the drum longer. If your machine does not have a cleaning cycle, turn the dial to the heavy-duty cycle, set the water temperature to hot, and choose an extra rinse cycle.
- Let the cycle run completely: Start the machine and let the cycle finish without interruption. If your washer has a pause button and smells unusually sour, let the drum fill with hot water, pause the cycle after ten minutes of agitation, and let the hot water soak inside the tub for 30 minutes before resuming.
- Wipe out leftover residue: Once the cycle finishes, open the door or lid. Take a damp microfiber cloth and wipe down the interior walls, the glass door, and the bottom wash plate. You may notice small flakes of loosened grime sitting at the bottom of the tub. Wipe those out by hand so they do not stain your next load of clean clothes.
Whenever you clean the tub, you must follow one critical chemical safety rule: never mix chlorine bleach with vinegar, ammonia, or any other household acid. Mixing bleach and vinegar triggers a chemical reaction that immediately releases toxic chlorine gas. Inhaling this gas causes coughing, burning eyes, and serious damage to your lungs. If your home has hard water and you want to use distilled white vinegar to dissolve chalky white lime scale, run a separate hot cycle using two cups of vinegar days later, only after your bleach cycle has rinsed out and drained completely.
Scrubbing the Rubber Door Seal, Soap Drawer, and Crevices
Running a hot drum cycle cleans the inner wash tub, but it will not reach the parts above the water line. The pull-out soap tray and door seals stay damp long after the cycle ends, making them the primary source of visible black mold and bad odors. You must scrub these areas by hand to get a truly fresh machine.
- Clean the pull-out soap tray: Pull the dispenser drawer open until it stops. Look for a small plastic locking tab, usually labeled "push" and located right behind the fabric softener compartment. Press that tab down with your thumb and pull the drawer completely out of the machine. Take the drawer to a sink and pull apart any removable plastic siphon cups.
- Soak and scrub the drawer parts: Fill your sink with warm tap water and a squirt of liquid dish soap. Let the drawer soak for ten minutes to soften caked detergent. Use an old toothbrush or a bottle brush to scrub the dried softener sludge from the corners, underside, and siphon tubes. Rinse the pieces with clean water and dry them with a towel.
- Wipe the empty drawer housing: Before sliding the drawer back, look inside the empty opening on the washer. The ceiling of this housing has tiny water spray nozzles that frequently gather dark mildew. Dip an old toothbrush into warm, soapy water and scrub the roof and walls of the housing. Wipe the loosened slime away with a damp rag, then snap the clean soap tray back into place.
- Clean the rubber door seal on front-loaders: The rubber door seal (gasket) around the front opening has deep folds that collect sitting water, lint, and loose coins. Use your fingers to gently pull back the rubber folds. Spray the inside surfaces with a mild bathroom cleaner or a mix of warm water and a splash of bleach. Use a soft sponge or cloth to wipe out the black slime trapped inside the groove. Pay close attention to the small drain holes at the very bottom of the rubber ring; if these holes are plugged with lint, clear them using a wooden toothpick so water can drain freely.
- Scrub top-loader rims and agitators: On top-loading machines, pull back the lid and inspect the top plastic ring just above the stainless steel basket. Water splashes against this rim during spin cycles, leaving a crust of lint and soap scum. Wipe down this plastic lip with warm soapy water. If your machine features a center agitator post that twists clothes through the water, pull off the top fabric softener cap and scrub out the gunk hiding inside the post. If your machine has a flat bottom wash plate (impeller) that moves laundry using water currents, scrub the seam around the plate edge. Learning the mechanical differences between agitator and impeller washing machines makes it easy to spot where lint gathers in your specific drum style.
Emptying the Drain Pump Filter and Daily Upkeep
If your clothes smell like sewer gas or your machine struggles to pump water out at the end of a cycle, the problem is often the drain pump filter (the lint and coin trap near the base). Front-load machines and some modern top-loaders have a small catch basin designed to trap coins, hairpins, buttons, and lint before they reach the electric drain pump. When this trap gets stuffed with debris, stagnant water collects around the pump blades and rots. You should empty this filter every two to three months.
- Cut the power and prepare the floor: Press the power button to switch the washer off. For complete electrical safety, unplug the power cord from the standard 120-volt 3-prong grounded wall outlet. Place a shallow baking sheet, a low plastic tray, and several thick old towels directly under the bottom of the washer, because trapped water will come out.
- Open the filter access door: Look at the bottom front corner of your washer. You will see a small square or rectangular plastic door. Press the latch with your finger or gently pry it open using a flat butter knife wrapped in a cloth.
- Drain the resting water: Most machines have a small, flexible black rubber drain hose clipped next to the round filter knob. Pull this hose out, direct the open tip into a shallow bowl, and pull the rubber plug out of the end. Let all the standing water drain out into your container. Once water stops flowing, push the rubber plug back into the hose and snap it back into its clip.
- Unscrew the main filter screen: Slowly twist the large round filter cap counterclockwise. Keep your towel pressed right against the opening, as an extra cup or two of water may spill out. Pull the filter assembly completely out of the housing.
- Clear the trap and inspect the housing: Dump any trapped coins, hairpins, or accumulated lint into the trash. Rinse the plastic filter under hot tap water and scrub away film with a soft brush. Shine a flashlight into the empty pump cavity inside the washer. Reach in carefully with your finger to confirm no stray objects are jamming the small plastic pump impeller blades at the back. Slide the clean filter back in and turn it clockwise until it stops firmly. Close the access panel door.
Once your washing machine is thoroughly clean, simple daily habits will keep mold from returning. You do not need to deep clean the machine every week if you prevent moisture from sitting trapped inside the dark tub.
- Leave the door or lid open: Keep the washer door cracked open at least two to three inches between loads so air circulates and dries out the tub naturally.
- Switch to low-suds HE detergent: Measure your laundry detergent carefully and use low-suds HE (High Efficiency) detergent to stop excess soap from coating the tub walls.
- Unload laundry right away: Move wet clothes to the dryer or clothesline as soon as the cycle ends so dampness does not create a sour odor.
- Wipe down the rubber seal: Keep an old towel handy in the laundry area to dry the bottom fold of the rubber door seal after your final wash load of the day.
- Ditch thick liquid softeners: Replace liquid fabric softener with a half-cup of plain distilled white vinegar in the rinse compartment to soften fabrics without leaving greasy sludge.
If you clean the drum, wipe the seals, and clear the drain pump filter, yet the washer still fails to pump water out or produces a persistent burning electrical smell, stop running cycles. A failing drain pump motor or a cracked internal drain hose requires hands-on repair. At that point, unplug the unit from the wall outlet and contact a qualified appliance repair professional to inspect the internal plumbing.
FAQs
How do I get rid of the sour smell inside my washing machine drum?
To eliminate a sour smell, run an empty cycle using the hottest water setting with a washing machine cleaning tablet or one cup of liquid chlorine bleach. The high heat and sanitizing agent dissolve the sour soap scum coating the outside of the wash basket. After the cycle finishes, wipe down the inside walls and leave the door open so the drum dries completely.
Can I use vinegar and baking soda together to clean my washer?
Mixing vinegar and baking soda together in the drum is not effective for deep cleaning. Baking soda is a base and vinegar is an acid, so mixing them creates a bubbling reaction that quickly neutralizes into plain saltwater and carbon dioxide gas. For better results, run an empty hot wash with a washing machine tablet or bleach first, and use vinegar alone on a separate hot cycle if you need to dissolve hard water scale.
How often should I clean my washing machine?
You should deep clean the wash drum and wipe down the rubber door seals once every month to keep mold and soap scum under control. The lower drain pump filter should be cleared of trapped lint, coins, and debris every two to three months. If you wash heavily soiled work clothes, pet bedding, or do more than seven loads a week, clean the machine twice a month.





















