Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Why Is Your Washer Making a Clicking Noise?

Prime for Young Adults: check your eligibility on Amazon

Pause the cycle right away to check inside the wash basket for stray metal items. Most sudden clicks happen when loose coins, heavy buckles, or stray bra wires tumble against the inner tub or slip into the rim. An empty drum usually points to something mechanical, like the door safety latch locking into place or a worn plastic tooth slipping underneath.

Finding the real culprit depends on where the sound starts and when it happens during the wash. A single loud click right before the tub starts turning is usually just the lid switch doing its normal job. Rapid, steady clicking during the wash cycle often means a worn plastic gear underneath, while tapping during water drainage points to debris trapped in the drain pump filter (the catch basket that stops lint and coins). Follow these simple checks to pinpoint the sound and fix it safely.

Normal Machine Clicks Versus Warning Sounds

Washing machines make dozens of mechanical sounds during a normal laundry cycle. Some of these clicks are completely healthy and show that your machine is operating properly. Other clicking sounds indicate that something is trapped, loose, or wearing out. Knowing the difference right away keeps you from worrying needlessly or running a cycle that could damage your appliance.

A single, crisp click at the start of a cycle is almost always normal. Modern washers rely on the lid latch assembly (a safety lock that clicks shut before the tub spins) to prevent injuries. You might hear this lock click once when you press start, and click again if you pause the load to add a stray sock. You will also hear distinct clicks as internal electronic switches open and close water valves or switch the motor between different wash speeds.

Many modern washers also use an electric shift actuator underneath the tub to switch between washing and spinning. When the cycle changes from soaking to agitating, this part makes a distinct mechanical snap. That single click simply means the gears have moved into place. You may hear another click when the wash finishes and the pump turns on.

A warning click sounds very different. Instead of a single clean snap between cycle phases, an abnormal noise is usually repetitive, rapid, or tied directly to the speed of the spinning drum. If the clicking speeds up as the inner wash basket spins faster, a hard object is likely striking the metal wall. A steady, rapid clicking during the wash cycle often points to slipping gears, loose drive belts, or a stuck pump.

Pay close attention to any extra symptoms that accompany the noise. If you smell burning rubber, notice hot plastic odors, or see water pooling on the floor, shut the washer off immediately. Unplug the power cord from the standard 120-volt 3-prong grounded wall outlet right away to prevent electrical hazards. A harmless machine click never produces burning smells, heavy vibration, or water puddles.

Loose Items Trapped Inside the Clothes Tub

The most frequent source of unexpected clicking is a loose piece of metal tumbling inside the stainless steel clothes tub. Loose pocket change, keys, hairpins, screws, bra underwires, and heavy jacket zippers create a sharp tapping noise every time the basket turns. If a small item slips through the tiny gap between the spinning inner basket and the outer plastic tub, it can scrape along the walls throughout the entire cycle.

How you inspect the drum depends on your washer style. In models with a flat bottom wash plate (impeller) that moves laundry using water currents, coins often slide underneath the outer edge of the plate. Washers with a tall center post face different hazards, as bra underwires frequently snag on the post base. Understanding the difference between agitator and impeller washers helps you know where tiny items hide when the basket is empty.

Check your clothes tub thoroughly before assuming an internal motor part has failed:

  • Unplug the washing machine from the wall outlet so the drum cannot turn unexpectedly.
  • Rotate the empty wash basket slowly by hand while listening closely for scraping or rattling sounds.
  • Shine a bright flashlight through the small drain holes in the stainless steel tub to spot wedged wire or nails.
  • Run your fingers carefully along the front rubber door gasket folds if you own a front-loading machine.
  • Look closely around the bottom rim of the wash plate or center agitator post for wedged coins or buttons.

If you find a trapped coin or hairpin wedged in a basket hole, pull it out gently using needle-nose pliers. Leaving a metal object wedged in the drum can tear delicate fabrics in future loads and eventually punch a hole in the outer wash tub. Always check your pockets before loading dirty clothes into the machine to keep this from happening again.

Clicking During Drainage and Clearing the Catch Basket

If your machine stays quiet while washing but begins clicking loudly when water empties, the issue sits inside the drainage system. Washers use a built-in drain pump that pushes water up into a kitchen sink or standpipe. As dirty water rushes out of the tub, light debris like coins, bread bag clips, toothpicks, and buttons get sucked along with the flow.

These foreign objects end up inside the drain pump filter (a small catch basket that traps debris before water drains out). Inside the pump housing, a plastic impeller blade spins at high speeds to force water out through the drain hose. When a hard object enters this chamber, the spinning plastic blades smack against it repeatedly, creating a fast, loud clicking or chattering sound.

You should clean out this catch basket immediately to prevent the pump motor from seizing or burning out. Grab a shallow baking pan, a few old bath towels, and follow these steps to clear the clog safely.

First, turn off the washer and disconnect the power plug from the wall. If the tub is still full of hot water, wait for it to cool down before opening anything so you do not burn your hands. Keep a bucket and several dry towels close by to protect your flooring.

Second, locate the pump access door. On most front loaders, this is a small square flap near the bottom front corner. Many compact top loaders also provide a lower access panel, while standard top loaders may require looking underneath the cabinet. Whether you use a front load or top load washing machine, your owner manual outlines the exact spot where the pump catch is housed.

Third, lay your towels flat on the floor directly beneath the access door and place your shallow pan under the drain spout. Most machines have a small rubber emergency drain tube next to the filter cap. Pull the plug on this small tube first to drain the resting water into your pan, then replace the plug.

Fourth, twist the main filter cap counterclockwise to slide the basket out. Water will spill out, so keep your pan in position. Remove any coins, lint clumps, bobby pins, or small socks trapped in the basket. Reach your finger into the pump opening to confirm the plastic impeller fan turns freely without catching on hidden debris.

Fifth, rinse the catch basket clean under a faucet, push it back into the housing, and twist the cap tightly clockwise until it stops. A loose filter cap will leak gallons of water across your laundry room floor during the next rinse cycle. Turn the power back on and run a quick rinse cycle to verify the clicking sound is gone and the cap is watertight.

Mechanical Clicking from Worn Drive Parts Underneath

When the wash basket is empty and the drain pump is clear, a persistent clicking sound points to mechanical wear under the tub. Top-loading washers with a center wash column rely on agitator dogs (small plastic directional teeth inside the center wash post). These small plastic cams allow the top half of the center post to spin in only one direction to pull clothes down into the water.

Over several years of heavy use, these plastic teeth wear smooth. When the motor reverses direction during the wash cycle, stripped teeth slip across the internal gear tracks rather than locking into place. This slippage creates a steady, rhythmic clicking or ratcheting noise from the center post while the bottom half still agitates. Replacing worn agitator dogs is an inexpensive repair that most homeowners can finish with a simple socket wrench and a screwdriver.

Another mechanical culprit underneath the machine is the shift actuator or clutch assembly. This small electronic component moves a plastic gear arm to switch the transmission between the gentle agitation motion and the high-speed spin cycle. If the internal motor of the actuator weakens or its plastic teeth chip, it struggles to lock the gears into position. The machine will click several times in rapid succession as it tries and fails to engage the spin basket.

You should also inspect the drive pulley (a metal wheel underneath that turns the belt) if you hear a clicking sound underneath the machine that speeds up with the motor. A loose retaining nut can cause the pulley to wobble, striking nearby brackets on every rotation. A worn drive belt with missing rubber teeth can also create a rhythmic clicking as it passes over the motor shaft.

Stop running cycles and contact a professional appliance repair technician if the clicking turns into a loud metal-on-metal screech or if the wash tub wobbles violently while hitting the machine frame. Continuing to wash heavy loads with broken drive gears or loose pulleys can warp the transmission shaft or crack the outer plastic water tank, turning a minor part replacement into a ruined appliance. If you see grease splattered under the washer or notice water dripping from the center transmission shaft, call for professional service right away.

FAQs

Why does my washer click several times right before it begins to spin?

This sound is usually the shift actuator moving mechanical gears to engage the spin cycle. The machine pauses the motor, locks the lid latch assembly, and shifts drive components beneath the tub. If it clicks three or four times and spins normally, the operation is standard. If it clicks constantly without ever spinning, the shift actuator or lid switch has failed.

Can a clicking washing machine damage my clothes or cause a leak?

Yes, depending on what causes the noise. A bra underwire or hairpin trapped in a drum hole can snag fabric, rip holes in shirts, or scrape the outer water tub until it leaks. Hard items rattling in the drain pump can crack the plastic impeller housing and spill water across your floor. Addressing the clicking sound promptly prevents these costly secondary problems.

How do I know if my washer agitator dogs are stripped and making noise?

Try turning the top section of your center agitator post by hand with the machine off. The top section should turn smoothly in one direction and lock firmly when turned the opposite way. If the top section spins freely in both directions or makes a clicking sound when you turn it, the small plastic directional teeth inside are stripped and need replacement.

4.7
3 ratings
George Johnson
WRITTEN BY
George Johnson
Hi, I'm George. My Denver base is the perfect testing ground for all things home appliances. Small gadgets are my thing, and I've been exploring them for 15 years. I also have a degree in Consumer Science, just for some extra street cred.