Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How to Fix an LG Washer That Won't Drain

Prime for Young Adults: check your eligibility on Amazon

A quiet chime signals the wash is done, but opening the door reveals a tub full of gray water and soaking clothes. The machine usually stops emptying because of a clogged drain filter or a kinked drain hose behind the cabinet. Small items like coins, hairpins, and thick lint get caught in the lower screen, blocking water flow. Clearing that trapped debris usually gets the water moving again in minutes.

The exact fix depends on the design and what the control panel shows. Front-load washers have a small clean-out door near the base, while top-load models route drainage differently. An OE error message confirms the water cannot pump out. Sound also gives a clue, as a gentle hum means a trapped object is jamming the pump wheel, while total silence suggests a motor issue. Here is how to safely drain the drum and clear the blockage without flooding the room.

How do you drain standing water without making a mess?

Opening your washer door while the stainless steel clothes tub is half-full of water will send gallons pouring across your laundry room floor. Front-load washers lock their doors automatically when water levels sit too high, but forcing that door open or running more cycles will only make the mess worse. The safest move is to remove the standing water through the built-in emergency drain tube before touching anything else.

Before you begin, always pull the power plug from your standard 120-volt 3-prong grounded wall outlet. Working around standing water with an appliance connected to live electrical power creates a serious shock hazard. Once the machine is unplugged, grab several old bath towels, a shallow baking dish or oil drip tray, and an empty five-gallon bucket.

  1. Locate the lower access door: Look at the bottom front corner of your front-load LG washer. You will see a small rectangular access flap. Press the small tab on the side or top of the flap, or insert a flat butter knife wrapped in tape, to pop the door open.
  2. Set up your catch tray: Spread a thick bath towel on the floor directly beneath the door opening. Place your shallow baking pan flat against the base of the cabinet, right under the components inside.
  3. Unclip the emergency drain tube: Inside the opening, you will see a round cap and a small black rubber hose clipped to the side. Unsnap this small rubber tube from its plastic retaining clip. Pull it forward gently so it extends over your shallow pan.
  4. Remove the hose plug: Hold the tip of the hose firmly over the pan and twist the small plastic plug out of the end. Water will begin running out immediately. Let the shallow tray fill halfway, slide the stopper back into the hose to pause the flow, and empty the pan into your five-gallon bucket.
  5. Repeat until the tub is empty: Pull the plug again and repeat this process until water stops flowing from the tube. This can take ten to fifteen minutes if your washer is completely full, but it protects your flooring from major water damage.
  6. Reseal and secure the tube: Push the plastic plug tightly back into the tip of the drain hose. Clip the hose back into its storage bracket so it stays out of the way.

If you have an LG top-load washer, it will not have this front access door. For top-load units, scoop as much water as possible out of the inner wash basket using a plastic kitchen bowl. Once the water level drops below the halfway mark, pull the wet laundry out piece by piece and squeeze excess moisture back into the basket before setting the clothes in a laundry basket.

How do you clean the LG drain pump filter?

Once you remove the standing water, you can safely open the coin trap. The drain pump filter is a small catch screen that traps coins and lint before wastewater enters the pump motor. When hairpins, loose change, baby socks, or dense bundles of pet hair slip past the wash basket, they collect right here and stop water from flowing out.

Top-load washers do not use a user-accessible lower front filter, which is an important maintenance detail when considering if a front-load or top-load washing machine is better for your home. On front-load models, clearing this catch screen is the single most common fix for drainage failures. Follow these steps to clear it safely:

  1. Keep your towels in place: Even after draining the emergency tube, a cup or two of residual water remains inside the pump chamber. Keep an absorbent towel tucked under the round filter cap.
  2. Turn the filter handle counterclockwise: Grip the round knob located next to the drain tube. Turn it to the left. It may feel stiff if mineral deposits or trapped debris have jammed the plastic threads. Turn firmly until the threads release.
  3. Pull the filter cylinder out: Slide the plastic filter straight out of the machine housing. A small splash of water will spill into your towel, which is completely normal.
  4. Rinse away trapped debris: Take the plastic screen to a nearby utility sink. Pull away thick mats of lint, dog hair, or stray fabric threads. Wash the screen thoroughly under warm running tap water and scrub the mesh with an old soft toothbrush to remove slimy detergent film.
  5. Inspect the empty pump chamber: Shine a flashlight directly into the round opening left in the washer cabinet. Look for quarters, bra underwires, or plastic tags that slipped past the screen. Carefully reach inside with a fingertip to confirm the chamber is clear.
  6. Reinstall the filter properly: Line up the plastic guide ribs on the filter with the grooves inside the pump housing. Push the filter in flat and turn clockwise until it is snug and the handle sits in a vertical orientation. Do not cross-thread the cap, or water will leak during the next cycle. Close the outer access flap.

Is your drain hose kinked, clogged, or installed wrong?

If the filter is clean but your machine still holds water, the issue usually sits along the discharge path. LG washers use a built-in drain pump that pushes water up into a kitchen sink or standpipe. If the path is pinched, placed too high, or shoved too far into the plumbing, the pump cannot overcome the resistance. Walk through this checklist to spot the problem:

  • Clearance behind the cabinet: Pull your washer forward slightly. Verify that you have at least 4 to 6 inches of rear clearance. If the washer was pushed back tight against the drywall, the flexible ribbed drain hose can easily crimp flat, cutting off water flow like a folded garden hose.
  • Standpipe height requirements: Check where the drain hose enters the wall pipe. The standpipe is the wall drain pipe that takes waste water away. LG requires the top of this pipe to sit between 29 inches and 96 inches off the floor. If your wall pipe rises higher than 96 inches, the pump motor lacks the power to lift heavy water that high. If it sits lower than 29 inches, water will siphon straight out of the tub while filling.
  • Hose insertion depth: Look at how far the curved plastic elbow extends into the standpipe. The hose should only slide down 4 to 6 inches into the hole. If someone pushed two feet of hose down into the wall, wastewater can back up or siphon backward into the machine.
  • Proper air gap: Confirm that the drain hose is not taped airtight to the wall standpipe. The connection requires an open gap around the hose so air can move freely. Sealing it with duct tape creates a vacuum lock that stops the pump from moving water.
  • Internal hose clogs: Disconnect the hose from the wall standpipe and lower it into a five-gallon bucket near the floor. If water trickles out slowly or nothing comes through, lint and compacted soap scum have clogged the line. Run warm water through the hose from a utility sink tap or gently run a flexible plumbing snake through it to dislodge the plug.

What does the LG washer OE error code mean?

An OE message glowing on your LG washer display is the official drain failure code. It stands for Output Error. This code appears whenever the washer control board detects that water has not pumped down to an empty level within ten to thirteen minutes of continuous pump operation. The computer pauses the cycle, sounds an alert chime, and stops the machine to prevent the motor from burning out.

Clearing the screen filter or straightening a pinched hose resolves the physical blockage, but the computer often retains the error memory. You need to reset the electronic controls so the washer recognizes that it can safely run again. Here is the standard reset procedure:

  1. Press the POWER button to turn the control display off.
  2. Unplug the main power cord from the 120-volt wall outlet.
  3. While the unit remains completely unplugged, press and hold both the POWER and START/PAUSE buttons down simultaneously for 5 seconds. This discharges leftover electrical current stored inside the internal circuit board capacitors.
  4. Plug the power cord directly back into the wall outlet. Avoid lightweight extension cords, which cause voltage drops that confuse modern appliance sensors.
  5. Power the machine on. Select a spin-only setting or run a quick wash cycle with no clothes inside to confirm that the OE code has cleared and water drains rapidly.

Another common cause of mystery OE codes is detergent oversudsing. Standard laundry detergents create massive suds blankets that confuse the water pressure sensor. Always use low-suds HE (High Efficiency) detergent in your machine, and use only two tablespoons per standard load. If thick suds fill the tub, the pump pushes air pockets instead of water, triggering a false drain error. Running a cycle with a cup of white distilled vinegar and hot water will dissolve these suds and clear the sensor line.

Is your drain pump jammed or completely broken?

When the drain paths are clear and the filter screen is empty, the pump hardware itself requires a closer look. A built-in drain pump uses an electric motor that spins a small internal wheel to push water up the hose. Understanding what is happening inside the pump housing helps you decide whether you can handle the repair yourself or need a service technician.

The impeller is the small spinning plastic wheel inside the pump chamber. Knowing the difference between a jammed impeller and a dead motor comes down to what you hear and feel:

  • A humming or buzzing sound: If the washer enters the drain cycle and you hear a distinct, low electrical hum coming from the bottom of the machine, the motor is receiving electricity. However, the plastic impeller wheel cannot rotate. A small coin, toothpick, or piece of wire often slips past the screen and wedges between the impeller blades and the housing wall.
  • How to check the impeller manually: Unplug the washer from the wall outlet. Remove the round filter screen again and look directly into the small hole in the back of the chamber. You will see the plastic impeller blades. Reach in with your index finger or a wooden chopstick and gently nudge the blades. The wheel should turn with a slight springy resistance (half-turns). If it is locked solid, pry out the trapped object. If the wheel wobbles loosely on its metal pin, the plastic shaft has broken.
  • A grinding or rattling noise: If the pump makes a harsh, clattering noise during drainage, foreign objects are bouncing against the spinning blades, or the plastic blades have chipped off. A damaged impeller cannot push enough volume to empty the tub before the computer timer runs out.
  • Total silence: If the cycle reaches the drain stage, the timer counts down, but the lower cabinet makes no sound at all, the motor winding has failed, the electrical wire harness has rattled loose, or the main control board relay has burned out.

If clearing physical debris allows the impeller to spin freely, your washer should return to normal operation immediately. But if the pump motor stays completely silent, leaks water around its drive shaft, or emits a sharp electrical burning smell, the entire pump assembly needs replacement. Replacing a drain pump involves unmounting the lower cabinet brackets, disconnecting wire clips, and swapping the pump housing. If you are uncomfortable working with wire harnesses and hose clamps, shut off the water valves, unplug the machine, and contact a certified appliance repair professional.

FAQs

Why won't my LG top-load washer drain water?

Unlike front-load models, top-load LG washers do not feature a front cleanout door. Drainage failures on top loaders are usually caused by a kinked rear drain hose, a failed lid switch, or clothing items that slipped over the top of the inner wash basket. If small socks work their way down between the basket and the outer tub, they travel straight into the pump intake and jam the mechanism.

Can using too much detergent stop an LG washer from draining?

Yes, adding too much soap or using regular non-HE soap creates excessive foam that fills the drain housing. The drain pump is designed to move liquid, not airy foam. When thick suds enter the pump cavity, the impeller spins in an air pocket without moving water, which triggers the OE drain failure code. Always use low-suds HE (High Efficiency) detergent measured to the manufacturer lines.

How do you force an LG washer into a drain and spin cycle?

To run a drain and spin cycle without adding more water, power the washer on and do not turn the cycle selector knob. Immediately press the Spin Speed button to choose your desired spin level, then press the START/PAUSE button. The washer will bypass the wash phase, engage the drain pump immediately, and spin the excess water out of your clothing.

How often should you clean the LG drain pump filter?

LG recommends inspecting and cleaning the lower coin trap filter once every month, or at least every thirty to forty wash cycles. Households with heavy pet shedding, cloth diapers, or frequent outdoor clothing loads should clean the filter every two weeks. Regular cleaning prevents dense lint accumulation that burns out the electric pump motor.

5
1 ratings
Nicholas Ellis
WRITTEN BY
Nicholas Ellis
Nicholas is a home appliances editor based in Phoenix, Arizona. He is known for her expertise in modern kitchen appliances and their utilization in healthy cooking practices. With over 8 years of experience in the field, he brings a unique perspective in her reviews and guides.