Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Is It Safe to Leave a Washing Machine Plugged In All the Time?

Prime for Young Adults: check your eligibility on Amazon

Many people assume an appliance should be unplugged after every load to prevent a fire. Usually, a washing machine can stay plugged in between uses if the cord and outlet are in good shape and it’s set up as the manual directs.

That answer changes if the plug or outlet feels unusually warm, looks damaged, or is close enough to get wet. The outlet also needs to suit the machine and its location, and the manual may advise unplugging it during a long absence. Here’s what to check and what to do if you spot a warning sign.

Leaving it plugged in is usually fine between loads

A washing machine does not need to be unplugged after every load if its cord, plug, and outlet are in good condition and the machine is set up as its manual directs. A plug sitting in a sound, dry outlet does not by itself mean the machine is likely to start a fire while idle.

That answer changes if you notice heat, sparks, a burning smell, cracked or frayed parts, or water near the outlet. Those are warning signs, not things to watch and wait on. Stop using the washer and follow the steps below.

Check the washer’s manual for instructions about leaving it connected, especially if you’ll be away for a long time. Some machines may have specific directions for their controls or for extended periods without use. If the manual says to unplug the washer when it is not being used for a certain length of time, follow that direction.

The outlet also needs to suit the washer and the room. Use the type of outlet and electrical connection the manual calls for. A grounded outlet has a connection intended to give stray electricity a safer path. Don’t use an outlet that is loose, damaged, wet, or different from what the washer instructions require.

Check the cord, plug, and outlet before use

Before starting a load, look over the parts you can see. You don’t need to open the washer or remove an outlet cover. If anything looks damaged, leave the machine off and arrange for help.

  • Look along the full cord. Check for cuts, cracked or melted spots, exposed wires, and places where the cord is pinched behind the washer. A cord trapped under a machine or bent sharply against a wall can become damaged over time.
  • Look at the plug. Check for cracks, dark marks, melted areas, or bent parts. The plug should sit securely in the outlet rather than drooping or slipping out.
  • Look at the outlet. Check for cracks, scorch marks, looseness, or signs that it has been wet. The outlet should be dry, and water from a leak or splash should not be able to reach it.
  • Notice heat and smell. A plug or outlet that feels unusually warm, or smells burnt, needs attention. Don’t keep running the washer to see whether the warning goes away.
  • Check the setup. Make sure the washer is connected as the manual directs. Avoid a lightweight extension cord or a power strip unless the manufacturer specifically says that arrangement is suitable.

Don’t pull the cord tight to make it reach, and don’t push the washer so far back that it crushes the cord. If the outlet is hidden behind the machine, turn the washer off and move it only if you can do so safely without straining hoses or the cord. Ask for help if the machine is too heavy or difficult to move.

Never touch a plug or outlet with wet hands. If the floor is wet, stay clear of the water and the electrical connection. Do not reach across a wet floor to unplug the washer.

Unplug it for long absences when appropriate

You usually don’t need to unplug the washer every time you leave home for a few hours. For a longer trip, check the manual and follow its advice. If the manual recommends unplugging the machine during an extended absence, do so before you leave, while the floor and your hands are dry.

If you can safely reach the plug, switch the washer off and pull the plug by its body, not by yanking the cord. If you cannot reach it without moving a heavy machine, or the plug is damaged or unusually warm, don’t force the job. Ask a qualified electrician or the manufacturer how to handle it.

Some people choose to unplug appliances while away for peace of mind. That can be reasonable when the plug and outlet are safe to handle and the manual allows it, but unplugging is not a fix for a damaged cord, a loose outlet, or water near the connection. Those problems need attention before the washer is used again.

Before leaving, look for signs of a leak around the washer and make sure the plug and outlet remain dry. If the machine has a water shutoff valve you can reach safely, check the manual for guidance on whether to close it during a long absence. Water shutoff advice can vary by washer and home setup, so don’t guess if the instructions are unclear.

Keep the outlet clear of water

Water and electricity are a dangerous combination. An outlet should not be exposed to splashes, a leaking hose, standing water, or a flooded floor. The washer’s location and electrical setup should follow the manufacturer’s instructions and suit the room.

If water is approaching the outlet or plug, keep away from the wet area. Don’t touch the washer, plug, outlet, or water to try to disconnect the machine. If you can reach the electrical breaker from a dry, safe place without crossing water, switch off the power to that circuit. If you can’t do that safely, stay clear and call for help.

Once water has reached an outlet or the plug, don’t use the washer again just because the floor looks dry. Have a qualified electrician check the outlet and wiring before power is restored. Contact the washer’s manufacturer if water may have entered the machine or reached its electrical parts.

A washer in an apartment, dorm, or RV still needs a dry, suitable electrical connection. Don’t assume an outlet is safe because it has worked before. If the outlet is near a sink, shower, floor drain, or plumbing that leaks, ask the property manager or a qualified electrician whether the location and setup are appropriate.

Stop using it if you notice heat or damage

If the plug or outlet is unusually warm, smells burnt, sparks, buzzes, or shows dark marks, stop using the washer. If there is no water and it is safe to touch, switch off the washer and unplug it by holding the plug body. If the plug is hot, sparking, damaged, or hard to remove, don’t touch it; switch off the circuit at the breaker only if you can reach it safely.

If you see smoke or flames, move away and call emergency services. Don’t pour water on an electrical fire. Get everyone away from the area, and don’t return until it is safe.

A damaged cord or loose outlet is not a reason to try a quick repair with tape or to keep using the washer carefully. Don’t open the outlet or attempt home wiring repairs unless you are qualified to do that work. Have an electrician repair or replace a damaged outlet, and ask the washer’s manufacturer about a damaged cord or machine connection.

Keep the washer unplugged, or leave the circuit switched off, until the cause has been addressed. If you rent, contact your landlord or property manager promptly and describe what you noticed. A burning smell, repeated sparks, or a plug that becomes hot deserves prompt attention even if the washer still runs.

Call an electrician or the manufacturer when needed

Contact a qualified electrician if the outlet is loose, cracked, scorched, warm, wet, or sparking, or if the plug will not stay firmly in place. A qualified electrician is a trained professional who works on home wiring. Don’t try to tighten an outlet or change wiring yourself.

Contact the washer’s manufacturer if the cord looks damaged, the machine’s instructions are unclear, or you need to know whether a particular outlet or setup is allowed for that model. Have the washer’s name and model information ready if you can find it on the machine or in the manual. The manufacturer can explain what its instructions require, but an electrician should handle concerns about the home’s outlet or wiring.

Keep the washer out of use until damaged or wet electrical parts have been checked and repaired. A machine that completes a cycle is not proof that its cord and outlet are safe. The safer choice is to resolve the warning sign before plugging it in again.

Related guides: best pocket knife of all time and best edc knife of all time.

5
2 ratings
Betty Smith
WRITTEN BY
Betty Smith
On a rainy Seattle day, you might find Betty Smith, our female home appliances editor, tinkering with her latest gadget. With a degree in Mechanical Engineering and 15 years of experience, Betty crafts practical tips and DIY repair guides that have resonated with readers nationwide.