Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How Wide Is a Washing Machine, and Will It Fit?

Prime for Young Adults: check your eligibility on Amazon

There’s no single width for every washing machine. The exact measurement depends on the model, so check its listed width before deciding it will fit your laundry space.

Compact and portable washers may be narrower than other designs, and controls or other parts can stick out beyond the listed measurement. The washer also needs room for hoses and for its lid or door to open. Measure the tightest spot in the laundry area and along the route through doors and hallways. The steps below show what to check before you move or buy one.

Why Washer Width Changes From Model to Model

Washer width depends on the machine’s design and the exact model. A full-size washer, a compact washer, and a portable washer can take up different amounts of space, so one measurement cannot cover them all.

Even washers of the same general type may have different listed dimensions. Controls, handles, and other parts that stick out can affect the space you need, too. The number on a listing is useful, but it may not tell you whether the machine will clear your doorway or fit beside a wall.

Look for the exact model’s width on its product page or in its manual. If the listing gives several measurements, confirm which one is the width and whether the number includes any parts that stick out. When that detail is missing, ask the manufacturer or seller before you arrange delivery.

Check the Washer and the Space in Order

Measure both the place where the washer will sit and the route it must travel to get there. A washer can fit in a laundry nook but still get stuck at a hallway turn or doorway.

  1. Find the exact model’s listed width. Open the product page or manual and look for the dimensions. Write down the width for the precise model, not just a similar machine in the same series. This gives you the measurement to compare against your space.
  2. Check what the width includes. Look for a diagram or note showing whether the measurement includes controls, knobs, handles, or other parts that stick out. If the listing does not say, contact the seller or manufacturer. A small projection can matter when a washer has to slide past a door frame or sit close to a cabinet.
  3. Measure the place where the washer will sit. Use a tape measure across the opening at the narrowest point. Check near the floor and higher up, since trim, a counter edge, or a pipe may make one part tighter. Keep the tape straight and measure from the surfaces the washer will actually sit between.
  4. Measure the route into the room. Check the clear width of each doorway and hallway, plus tight corners along the way. Measure between the door frame, not from the outside edges of the trim. Include any turn where the machine may need to angle around a wall or cabinet.
  5. Compare the machine with each measurement. The washer must clear the narrowest part of the route and fit in its final space. Don’t assume a delivery crew can tilt or turn it through a gap that is too tight. If the numbers are close, confirm the required space with the manufacturer and delivery provider before ordering.
  6. Plan room for connections and opening the washer. Check the manual or installation instructions for space around the sides and back. Make sure hoses will not be crushed and that the lid or door can open fully. This helps the washer work in the space, not just slide into it.

Measure more than once if a wall, cabinet, or door frame is uneven. Use the smallest measurement as your available space. That is the number that matters when a machine needs to pass through or sit in a tight opening.

Check What Sticks Out and What Needs Room

Product dimensions are the measurements listed for the washer. They may not describe every part that affects a close fit, so compare the listing with the machine’s diagram and installation instructions.

  • Controls and handles: Check whether knobs, buttons, or handles extend beyond the main body. A part that sticks out may catch on a door frame or stop the washer from sitting flush between cabinets.
  • Hoses behind the washer: Leave the rear space specified in the manual so water hoses and the drain hose are not sharply bent or pressed against the wall. The general planning guidance here is to allow 4 to 6 inches behind the washer for hoses, but the exact space depends on the model and its connections. Confirm the required amount in the installation instructions.
  • Side space: Check the instructions for any required room at the sides. A washer pushed tightly against a wall or cabinet may be hard to connect, move, or service. Extra room can also help prevent the machine from rubbing against nearby surfaces as it runs.
  • Lid or door movement: Open the lid or door as far as the design requires. Check that it will not hit a shelf, counter, wall, or another appliance. A washer that fits when closed may be awkward to use if the lid cannot open fully.
  • Floor and nearby fixtures: Look for baseboards, pipes, valves, and raised floor edges that could block the machine or its hoses. Measure around anything that cannot be moved, rather than measuring an empty opening on paper.

Clearance means extra room around the washer. It is not the same as the washer’s width, and the amount needed can vary by model. Follow the exact installation directions instead of assuming that a snug fit is acceptable.

When the Measurements Are Close

Compare the listed width with the smallest clear width of the space, then check the route separately. If the opening is wider than the listed washer body by only a little, do not treat that as proof that the washer will fit. Sticking-out parts, uneven walls, and the room needed to turn the machine may change the result.

For example, a washer may appear narrow enough for a laundry nook, but the doorway on the way there may be tighter. Or the body may fit between cabinets while the rear hoses press against the wall. Each part of the move and installation needs its own check.

If the listing does not explain whether controls or handles are included, ask for the full outside measurement, including anything that projects. You can also ask the delivery provider what measurements they need for the route. Get the answer before purchase or delivery, rather than relying on an estimate made at the door.

Do not force a washer through a tight opening or bend its hoses to make it sit in place. If the route is too narrow, ask the seller or delivery provider about the available options before the machine arrives. If the final fit is uncertain, pause and confirm the installation requirements with the manufacturer or a qualified installer.

FAQs

Where can I find the exact width of my washer?

Check the dimensions on the product page or in the manual for the exact model. Look for a diagram that labels width, and read any notes about parts that stick out. If the information is missing or unclear, ask the manufacturer or seller to confirm the full outside width.

Does the listed width include the knobs or handles?

That depends on how the manufacturer presents the dimensions. Look for a side or top diagram and a note explaining what is included. If there is no clear answer, confirm the measurement before buying, especially if the washer must pass through a narrow doorway.

How do I know whether a washer will fit through my doorway?

Measure the clear opening between the door frame at its narrowest point, then compare it with the washer’s full outside width. Also measure hallways and turns along the route. If the measurements are close, ask the delivery provider whether the washer can pass through that route before scheduling delivery.

How much room should I leave around a washer?

The needed space varies by model, so follow the installation instructions for the exact washer. Leave room for hoses behind the machine and enough space to open its lid or door. Check the sides, too, so the washer is not trapped tightly between walls or cabinets.

Related guides: best 24 inch wide washing machine.

4.5
2 ratings
Jessie Greene
WRITTEN BY
Jessie Greene
My name is Jessie Greene, a male home appliance expert from Los Angeles specializing in the luxury sector. For the past 12 years, I've been guiding consumers through the intricate world of high-end appliances.