How to Reset a Samsung Washing Machine Program
Clearing an active cycle usually takes nothing more than turning the power off and back on. A completely frozen screen needs a deeper reboot instead, which means unplugging the power cord for five to ten minutes to clear the machine's memory. These washers do not have a separate reset button, so cutting the electric supply is the only way to clear the controls.
The right next step depends on what the appliance is doing right now. A drum full of standing water will keep the door locked tight, while a repeating error code usually signals a clogged cleanout filter rather than a computer glitch. Sometimes the panel responds to touch, but the program refuses to advance. Here is how to stop the cycle safely, drain any trapped water, and unlock the door without making a mess.
Canceling an Active Cycle on a Samsung Washer
If your washer is running the wrong setting or you realized you dropped an item in the tub that belongs in the dry cleaner, you do not need to pull the plug right away. You can clear the program directly from the control panel. Follow these steps in order to cancel the active cycle safely:
- Press the Start/Pause button once firmly. This immediately halts the cycle, stops the stainless steel clothes tub from spinning, and closes the internal water inlet valves so no more water enters the drum.
- Press the Power button to shut the machine off. Powering down tells the control board (the electronic brain behind the buttons) to wipe the active program from its temporary operational memory.
- Wait between thirty seconds and two minutes for the automatic lid lock or front door lock to click open. The machine checks its internal safety sensors to make sure the inner wash basket has stopped moving completely and the water temperature is safe before opening the latch.
- Press the Power button to switch the washer back on. The display will wake up with a clean slate, clearing out the old timer and settings so you can pick a fresh program.
- Select your desired wash cycle or choose a drain-and-spin option. If the clothes tub already has water and detergent in it, selecting a drain or spin setting first will pump that soapy water out before you start over.
- Press Start/Pause to begin the new operation. The washer will recalibrate, sense the load weight, and begin the correct routine without carrying over any settings from the interrupted program.
If you press the Power button while the tub is spinning at high speed, the machine might pause for a moment before turning dark. Do not hit the button multiple times in frustration. Rapid button presses send mixed signals to the processor and can cause the system to freeze up entirely.
If your washer is a top-load model, the lid lock will usually disengage almost immediately after the wash plate stops moving. On front-load washers, the door remains firmly locked if the water level sits higher than the bottom of the door glass. In that scenario, powering down the unit will not unlock the door until that excess water is drained.
Performing a Hard Reset When the Controls Freeze
Modern laundry appliances function like small household computers. Electrical line noise, brief voltage drops, or rapid button presses can freeze the control board, leaving the screen stuck or completely unresponsive to your touch. Samsung washers do not have an external red reset button, so you must clear the memory manually.
To reboot a locked system, you need to perform a power cycle (unplugging the power cord for a few minutes). This process drains the residual electrical charge stored inside the electrical components so the microprocessors can start fresh. Follow these steps to perform a complete hard reset:
- Turn off the washer if the Power button responds. If the controls are completely frozen and the screen does not react at all, move directly to the next step.
- Unplug the power cord from the standard 120-volt 3-prong grounded wall outlet. Pull directly on the plug head rather than tugging on the cord itself to prevent damaging the internal copper wiring.
- Switch off the circuit breaker if the wall plug is inaccessible. Many heavy laundry pairs sit tightly tucked into small closets or under counters. If you cannot reach the cord safely, find your home electrical panel and flip the breaker labeled for the laundry room to the Off position.
- Wait between 5 to 10 minutes. Do not rush to plug it back in after ten seconds. The capacitors on the main control board store small amounts of electricity that keep internal chips energized for several minutes after disconnected from power.
- Press and hold the Power button for 5 to 10 seconds while the unit remains unplugged. This drains any stubborn electrical current left lingering inside the machine circuits.
- Plug the washer back into the wall outlet or flip the breaker back on. Avoid running the washer through a lightweight extension cord or an ungrounded adapter, as voltage drops can trigger another system freeze.
- Press Power and run an empty test cycle. Select a short wash or a spin-only setting to verify that the buttons beep, the display timer counts down normally, and the motor engages without stalling.
Draining Trapped Water to Unlock the Door Safely
One of the most frustrating problems is a frozen cycle that traps soaking wet laundry behind a locked front door. Samsung front-load washers feature an automatic door lock that relies on a water level pressure sensor. If that sensor detects standing water in the bottom of the drum, the latch stays locked to prevent five gallons of dirty water from spilling across your floor.
If your machine froze mid-cycle and resetting the power does not unlock the door, you must drain the water manually. Keep a shallow baking sheet, a low plastic container, and three or four old bath towels within arm reach before you begin. Here is how to empty the tub safely:
- Disconnect power to the washer. Unplug the unit from the wall outlet so no electrical components can activate while you work near standing water.
- Open the lower filter access door. Look at the bottom front corner of your front-load machine to find the small cleanout door. Press the plastic tab on the door edge to swing it open.
- Set down your towels and shallow tray. Place your towels directly beneath the access panel to catch stray drips, and hold your shallow container directly under the small black rubber drain hose.
- Remove the emergency drain cap. Unclip the small rubber hose from its plastic holder, hold the tip over your tray, and twist the plastic plug out of the hose end. Water will begin running out immediately.
- Drain the tub in stages. When your tray fills halfway, replace the rubber plug, empty the tray into a bucket or nearby sink, and repeat the process until water stops flowing from the tube.
- Inspect the drain pump filter. Once water stops exiting the hose, put the plug back on the tube and turn the large round filter handle counterclockwise to pull it out. The drain pump filter (the small cleanout door near the bottom front) often collects coins, hair pins, loose buttons, and thick lint mats that stop the pump from clearing water.
- Clean and reseat the filter. Rinse the plastic mesh under warm tap water, clear any debris out of the pump housing with your fingers, screw the filter tightly back into place clockwise, and push the rubber hose back into its storage clip.
Once you clear the standing water out of the drum, the water level sensor sends an empty signal. When you restore power, the door lock mechanism will click open, allowing you to pull your wet clothes out before they develop sour smells.
What to Check Before Resetting Persistent Error Codes
When your machine stops running and flashes an alert, that signal is an error code (the two-letter alert on the display screen). An error code tells you that a specific mechanical sensor reported a problem to the main board. Resetting the washer will clear the display for a few seconds, but the moment you start a cycle, the control board runs a self-check. If the mechanical issue still exists, the exact same code will return.
Instead of resetting the washer over and over, check the root cause associated with these common Samsung fault codes:
Drain Faults (5C, 5E, or ND): These codes mean the machine took longer than ten to fifteen minutes to drain the wash tub. Check the drain pump filter first to remove any lodged items. Next, inspect the ribbed drain hose behind the washer to verify it is not squashed flat against the drywall or kinked around a corner. If the hose pushes water up into a kitchen sink or standpipe, verify that the pipe is not clogged.
Water Supply Faults (4C, 4E, or NF): The machine tried to fill but detected little or no incoming water. Check both the hot and cold water supply hoses at the back of the machine. Ensure the water shutoff valves under your laundry sink or in your wall box are turned completely open. Unscrew the hoses from the back of the washer and check the small wire mesh inlet screens for sediment or hard water mineral buildup that chokes water flow.
Unbalanced Load Alerts (UB or UE): The off-balance safety sensor pauses spinning and beeps when bulky towels or heavy blankets bunch up on one side of the drum. Opening the door and redistributing the heavy items evenly around the inner wash basket solves this problem. Modern appliances rely on smart sensors to protect bearings, similar to how systems calibrate balanced spin cycles to handle heavy laundry without knocking the frame out of place.
Suds Warnings (SUD or Sd): This alert means the tub filled with excessive soap froth, blinding the pressure sensors and preventing the pump from moving water. Resetting the power will not clear the foam. You must let the washer sit idle for twenty to thirty minutes so the bubbles collapse on their own. Once the suds settle, run an empty cycle with cold water to flush out the drum. Always use low-suds HE (High Efficiency) detergent and measure carefully. Excess soap residue not only triggers pump errors but also collects mold inside the outer drum, so running occasional maintenance cycles to stop musty odors helps keep your machine running reliably.
Door Lock Errors (dC, dE, or LO): The machine cannot confirm that the lid or front door is shut tight. Look for clothing edges pinched in the door frame. Check for lint or dried soap inside the latch pocket on the washer frame that stops the door striker from engaging fully.
Signs of Hardware Failure That Need Professional Service
A software glitch or a minor clog can be resolved with a quick drain or a five-minute power cycle. However, some cycle freezes happen because a physical part inside the cabinet has failed completely. Repeating resets when a mechanical part is broken risks causing electrical shorts, damaging your flooring, or ruining the central computer board.
Stop trying to reset the machine and call an appliance repair professional if you notice any of these warning signs:
- A distinct burning plastic or electrical odor: This smell usually points to a seized drive motor, a shorted wire harness, or an overheating pump coil. Unplug the unit immediately.
- Continuous grinding, screeching, or buzzing sounds: If the washer hums loudly when trying to drain even though the cleanout filter is completely clear, the internal impeller blades of the pump may be broken or jammed internally.
- The circuit breaker trips instantly when you hit Start: If turning the machine on or starting the motor immediately snaps your household breaker, an internal component has suffered a dead short to ground.
- The control board remains completely dark: If you confirm that your wall outlet works by plugging in a lamp, but the washer display will not turn on or make a sound after a hard reset, the internal noise filter board or the main power control board has likely burned out.
- Water leaks pooling from underneath the machine frame: Puddles under the washer often indicate a torn rubber door boot, a split internal tub hose, or a cracked pump casing. Turn off both water shutoff valves behind the machine to prevent serious water damage to your subfloor.
FAQs
Where is the reset button located on a Samsung washing machine?
Samsung washing machines do not have a dedicated physical reset button anywhere on the cabinet or control panel. To reset the electronics, you must cancel the active cycle using the Power button or perform a hard reset by unplugging the power cord from the wall outlet for 5 to 10 minutes.
Why will my Samsung washer door not unlock after I turn it off?
The door remains locked because the safety sensor detects warm water standing inside the clothes tub or the drum has not come to a complete stop. Front-load washers will keep the door latch locked until the water level drops below the bottom edge of the door opening to stop water from flooding your floor.
Can running a hard reset clear recurring error codes permanently?
A hard reset will temporarily clear the error code from the digital display, but the code will return as soon as the problem occurs again. If the underlying cause, such as a clogged drain pump filter or a pinched water supply hose, is not resolved, the control board will pause the cycle and redisplay the fault code.
How do I run a drain and spin cycle after canceling a wash program?
Press the Power button to turn the machine on, but do not turn the cycle selector dial. Press the Spin button repeatedly until you reach your desired spin speed, then press Start/Pause. The washer will bypass the wash and rinse steps, activate the drain pump, and spin the excess water out of your garments.





















