How Does the Tub Clean Cycle Work?
There’s usually no reason to worry: Tub Clean runs the washer with no clothes inside to clear dirt and leftover soap from the tub. It uses water and cleaning action, much like a laundry cycle, but the washer is empty so it can clean the surfaces that normally hold clothes.
The exact steps depend on your washer. A top-loader and a front-loader may use different cleaning actions, and the manual will say whether to add a washer cleaner, bleach, or nothing at all. It also gives the right schedule and cycle details for your model. Here’s how to run it without guessing, and what to check if a musty smell or residue remains.
Leave the washer empty before you start
The Tub Clean or Drum Clean cycle is for the washer itself, not for a load of clothes. Take out laundry, including small items caught near the door or under the lid. Clothes can block water and cleaning action from reaching parts of the inside, and cleaner meant for the washer may be too strong for fabric.
The drum is the inside part that holds clothes. During ordinary loads, soap, dirt, lint, and moisture can collect around the drum and in areas you cannot easily see. Over time, that leftover material can contribute to a musty smell or visible residue. A cleaning cycle helps wash the inside of the machine without laundry getting in the way.
Before you begin, look inside for coins, hair ties, or other objects. If you have a front-loader, check the rubber seal around the door for loose debris. Remove anything you can reach safely, but do not pull or pry at the seal.
Let the washer follow its own cleaning sequence
The cycle usually fills the washer with water, moves or tumbles that water through the empty drum, and then drains it. Some washers also use a higher water temperature or a longer wash than a regular load. The exact steps depend on the washer, so the cycle name alone does not tell you its temperature, length, or water level.
A top-loader and a front-loader may move water differently. One may turn a center post or a flat plate at the bottom, while another tumbles the drum. Those differences do not change the main rule: leave the washer empty and use the cleaning instructions for your specific machine.
The cycle can loosen and flush away some soap film, dirt, and odor-causing residue. It cannot necessarily clean every hidden area, remove every stain, or fix a smell caused by a drain problem or another part of the washer. If the smell remains afterward, check the areas listed below rather than running the cycle over and over without finding the cause.
Choose the cleaner your manual allows
Use the washer manual as the deciding source before adding anything. Some washers call for a washer cleaner, some allow bleach, and some say to run the cycle without an added product. A washer cleaner is a product made to clean washing machines, but that does not mean every formula is suitable for every washer.
- Find the Tub Clean or Drum Clean instructions. Look in the manual or on the manufacturer’s support page for your washer’s exact model. If you no longer have the manual, the model information is often printed on a label on or inside the washer. Do not guess based on a different machine’s instructions.
- Check what the manual says to add. Follow its direction about whether to use a washer cleaner, bleach, or nothing. If the directions are unclear, contact the manufacturer before adding a product.
- Read the cleaner label. Confirm that the product is intended for washing machines and follow the label’s directions. Put it only in the place the washer manual or product label specifies.
- Do not mix cleaning products. Never combine bleach with a washer cleaner, detergent, vinegar, or another cleaner. Mixing products can create harmful fumes or other hazards. If you already mixed products and notice fumes or feel unwell, leave the area and contact emergency services or poison control for guidance.
- Keep regular laundry detergent out unless instructed. A Tub Clean cycle is not a detergent wash for clothes. Extra detergent can leave more suds or residue, which works against the purpose of cleaning the washer.
- Close the door or lid and start the named cycle. Keep your hands clear while the washer fills and moves. If the washer leaks, gives an error, or makes an unusual harsh noise, stop the cycle if you can do so safely and follow the manual’s troubleshooting instructions.
If you want help identifying a product made for this task, see this guide to washer drum cleaners. Still check your washer manual first, because a cleaner that is suitable for one machine may not be what another manufacturer recommends.
Follow the washer’s schedule instead of guessing
Manufacturers do not give one cleaning schedule that applies to every washer. The recommended timing may depend on the machine and how often you use it. Find the schedule in the manual, the washer’s display prompts, or the manufacturer’s care instructions.
- Check the manual for how often to run Tub Clean or Drum Clean.
- Look for a reminder on the control panel, if your washer has one.
- Follow any extra directions for frequent use, heavy soil, or recurring odor.
- Do not shorten or change the cycle unless the manual says that is allowed.
If you are unsure whether a cleaning reminder is overdue, use the manual’s guidance rather than choosing a schedule from another washer’s label or website. Cycle length also varies. The display may show the expected time, but the washer can adjust its estimate as it runs.
Check the door, drawer, and drain if odor stays
After the cycle ends, wait for the washer to unlock before opening it. Look for visible residue inside the drum and around the opening. If you see cleaner or leftover grime, follow the manual’s advice about wiping the area or running an additional rinse. Do not add another cleaner unless the instructions say to.
- Inspect the front-loader seal. Pull back the flexible rubber gently and look for lint, hair, or standing water in the folds. Wipe reachable debris with a clean cloth, following the manual’s directions. Keep fingers away from places you cannot see or reach safely.
- Check the detergent drawer. If the drawer comes out as described in the manual, remove it and rinse away visible soap buildup. Let it dry before putting it back. Do not force a drawer that feels stuck.
- Look for a blocked drain area. Some washers have a user-accessible filter that catches lint or small objects. Only open or clean it if the manual explains how, and prepare for water to spill. If the washer has no user-accessible filter, do not remove panels to search for one.
- Leave the door or lid open between loads. Once the washer is empty and safe to leave open, allowing the inside to dry can help prevent stale moisture from lingering. Keep the opening clear of children and pets.
- Check the washer’s drain hose and nearby drain. If water remains in the drum or a sour smell comes from the drain area, the hose or household drain may need attention. Follow the manual’s checks, and do not pull apart plumbing if you are not sure how to do it safely.
Residue can also come from using more detergent than the washer needs or from a product that creates too many suds. Follow the detergent package and washer manual, and use only the type of detergent the washer calls for. If the washer continues to show buildup, check its care instructions before changing products or repeating cleaning cycles.
Stop and get help when the washer shows a problem
Stop using the washer and contact the manufacturer or a qualified repair professional if water leaks from the machine, the cycle repeatedly stops with an error, or the smell continues after you have followed the manual’s cleaning and care steps. A persistent odor may come from a drain or an internal area that a normal cleaning cycle does not reach.
If you see smoke, smell burning, or notice a damaged power cord, keep away from the washer. Turn it off only if you can do so without touching water or damaged electrical parts, and contact a qualified professional. Do not remove panels or reach into the machine to investigate.
FAQs
Can I put clothes in during Tub Clean?
No. Remove all laundry before starting the cycle. The washer needs to clean its own inside, and clothes can block that cleaning action or be exposed to a product not meant for laundry.
Should I add detergent, bleach, or a washer cleaner?
Use only what your washer manual directs. Some models call for a washer cleaner, some allow bleach, and others call for no added product. Never mix cleaners or add regular detergent unless the manual specifically tells you to.
How long does the cycle take?
The time depends on the washer and its cycle design. Check the display or the manual for your machine’s expected time, and allow the cycle to finish rather than stopping it early.
What if the washer smells musty after cleaning?
Check the door seal, detergent drawer, and any user-accessible filter for moisture or residue, following the manual’s directions. Leave the door or lid open between loads so the inside can dry. If the odor continues or water remains in the drum, contact the manufacturer or a qualified repair professional.
Related guides: how to clean washer drum.





















