How Do You Properly Level a Washing Machine?
Many people assume a washer that shakes just needs to be pushed back into place, but that usually won’t fix the cause. Adjust the feet under the washer until all four sit firmly on the floor and the machine doesn’t rock. Then tighten any rings that hold the feet in place, following the instructions for your model.
Before adjusting anything, empty the washer and unplug it. The right way to turn the feet depends on how your machine is built, and an uneven or weak floor may need attention too. After making adjustments, check that the washer stays steady with a small load; if it still moves, stop and look for another cause. Start by checking for signs that the machine is sitting unevenly.
How to Tell If a Washing Machine Is Unlevel
A washer may be unlevel if it rocks when you press gently on a corner, if one foot does not touch the floor, or if the machine shakes or shifts during a spin. A small amount of movement in the clothes inside is normal, but the washer cabinet should stay steady.
An unstable washer can bang against nearby cabinets, make loud noise, or tug on its water hoses and drain hose as it moves. Repeated shaking can also put extra strain on the machine. A washer that is level and firmly supported is less likely to move across the floor.
Start with the washer empty. Clothes bunched on one side can make a properly leveled washer shake, especially during a fast spin. If the washer is empty and still rocks, or if it moves even with a balanced load, check its feet and the floor before running another cycle.
Prepare Safely Before Adjusting the Washer
- Turn the washer off and unplug it. This helps prevent it from starting while you are checking the feet. Keep the plug and your hands dry.
- Close the water shutoff valves if you need to pull the washer out. That reduces the chance of a hose being pulled loose. If you cannot reach the valves safely, stop and get help.
- Remove clothes and water from the washer. An empty machine is easier to steady, and a wet load can shift while you work.
- Make room to reach the feet. Pull the washer forward only as far as needed, and do not yank its hoses or power cord. Ask someone to help if the washer is too heavy or awkward to move.
- Check the manual for your model’s instructions. Some washers have adjustable feet, while others use a different method. Follow the manual if it gives a specific order or direction.
Do not crawl beneath a washer or tip it onto its side to reach a foot. If a foot is inaccessible without lifting the machine, or you see a damaged hose or a water leak, leave the washer unplugged and ask for qualified help.
Adjust the Washer One Foot at a Time
- Find the leveling feet. Look under the front corners first, then check the back corners. Leveling feet are adjustable supports under the washer; the manual can show their location if they are hard to see.
- Check whether each foot touches the floor. With the washer empty, press gently on opposite top corners. If the machine tips or clicks, one or more feet may be too high or too low. Keep your hands away from the gap under the washer.
- Identify which corner needs adjustment. Watch the feet as you gently press the washer. A foot that lifts from the floor is a clue that the washer is resting unevenly. Do not assume the shortest-looking foot is the only one that needs changing.
- Adjust one foot slightly. The adjustment may involve turning the foot itself or using a tool, depending on the washer. Check the manual before turning anything. There is no single direction that works for every model, so make a small change and check the result rather than forcing the foot.
- Set the foot firmly on the floor. It should support the washer without leaving a gap or making the machine lean. Avoid extending a foot farther than the manual allows, because too much extension can make the washer less stable.
- Check the other corners and adjust as needed. Press gently on the top corners again after each change. Adjust only the feet that need it, and make small changes until the washer sits flat without rocking.
- Check the washer from the front and side. The top should look level, but appearance alone is not enough. The washer also needs solid contact with the floor at every support point.
If you cannot tell which foot needs adjustment, or the feet turn loosely without supporting the washer, stop and check the manual. A loose or damaged support may need repair rather than more turning.
Secure the Feet and Check for Rocking
- Look for lock nuts on the feet. Lock nuts are rings that keep the feet from turning. Some washers have them and some do not, so use the manual to identify the parts.
- Tighten the lock nuts if your washer has them. Hold the foot in position while tightening the ring as directed in the manual. This helps keep the setting from changing as the washer runs.
- Press gently on each top corner again. The washer should not rock or click, and the feet should remain in contact with the floor. If it rocks, make another small adjustment and repeat the check.
- Check that the washer is not pressing on nearby items. Leave enough space for the machine to run without hitting a wall, cabinet, or storage item. Make sure the hoses are not stretched, trapped, or bent sharply.
- Move the washer back carefully if you pulled it out. Keep the cord and hoses clear as you slide it into place. Check the feet again afterward, since moving the washer can change how it sits.
Do not put folded cardboard, loose wood scraps, or other objects under a foot to make up for unevenness. These can slip or compress, allowing the washer to rock again. Use the adjustment method allowed by the washer’s manual.
What to Do If the Floor Is Uneven
If one area of the floor dips or slopes, the washer’s feet may not be able to correct it safely. The washer can seem steady at first, then move when the load shifts during spinning. Look for a soft, damaged, or visibly sloping area around the machine.
If the floor is firm and only slightly uneven, adjust the feet within the limits in the washer’s manual. If the feet are already extended as far as the manual allows, or the machine still rocks, do not keep raising them. A properly sized, stable washer support may be an option, but confirm that the washer’s manufacturer allows it and follow the support maker’s directions.
A floor that flexes, sags, feels soft, or is damaged needs more attention than a foot adjustment. Stop using the washer if the floor gives under its weight or the machine shifts dangerously. Ask a qualified flooring professional or contractor to assess the floor, and contact an appliance repair professional if the feet or washer frame appear damaged.
Confirm the Washer Stays Steady During a Cycle
- Reconnect the washer only after the feet are secure. Open the water valves if you closed them, and look for drips around the hose connections before starting a cycle.
- Begin with a small, balanced load. Spread items around the inner wash basket instead of piling them on one side. A large, tangled item can throw the load off balance even when the washer itself is level.
- Stay nearby during the spin cycle. Listen for banging and watch for the machine walking across the floor. Stop the cycle if the washer moves hard or a hose pulls tight.
- Recheck the feet if shaking returns. Unplug the washer before touching or adjusting them. Also make sure the load was not bunched to one side.
If a balanced load still causes strong shaking after the washer is steady by hand, stop the cycle and check the manual’s troubleshooting advice. The problem may not be the floor or the feet. Contact an appliance repair professional if the washer keeps banging, moves sharply, or shows signs of damage.
FAQs
Should I unplug the washer before adjusting its feet?
Yes. Turn the washer off and unplug it before checking or adjusting the feet. If you need to pull it out, avoid stretching the cord or hoses, and close the water valves if the hoses could be pulled.
Which way should I turn the leveling feet?
The direction depends on the washer model and how its feet are built. Check the manual before turning a foot, then make a small adjustment and check whether the washer sits more steadily. Do not force a foot that will not turn.
Why does the washer still shake after I level it?
A load piled to one side can make even a level washer shake during spinning. An uneven or weak floor, a foot that has not been secured, or a problem with the washer can also cause movement. Stop the cycle if the machine shifts forcefully, then check the load and feet before calling for repair help.
Can I put something under a washer foot?
Do not use loose scraps or folded material as a quick fix because they can move under the washer. Check the manual for an approved support method if the floor is uneven. If the floor is soft or the washer still rocks, get qualified help instead of raising the feet beyond their allowed adjustment.
Related guides: washing machine water level switch adjustment and how to bypass washing machine water level sensor.





















