Topappliancesreviews.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Can You Safely Build Your Own Washer and Dryer Pedestals?

Prime for Young Adults: check your eligibility on Amazon

Yes, a homemade stand can work. It must fit each machine, hold its full weight, and stay steady while the washer spins. A stand that shifts or rocks can let an appliance move, damage the floor, or cause an injury. Raising the machines also shouldn’t block anything the manuals say must remain clear.

The right design depends on each machine’s size and weight, where its feet need support, and how firmly the frame is built and joined. The finished stand and the floor beneath it must be level, too. Check both manuals before choosing a height or starting construction. Then measure, build, and set up the machines in a way that helps you spot problems before use.

The Short Version

  • A raised platform is safe only if it fits the appliance, supports its weight at the right points, and stays firm and level while the washer spins.
  • Check both appliance manuals before planning. They may limit how a machine can be raised or what kind of support it needs.
  • Measure each machine and the space around it, then build a rigid frame with secure joints and supports that prevent side-to-side sway.
  • If you cannot confirm the platform’s strength, fit, and stability, don’t put the machines on it. Use a suitable purpose-built stand or ask a qualified professional for help.

What Makes a Homemade Pedestal Safe?

A washer pedestal has to do more than hold the machine’s weight while it sits still. During a spin, an uneven load can make the washer shake and push against its support. A weak or rocking platform can shift, damage the floor, or allow the machine to fall.

Safe support depends on four things: the machine’s weight, the places where its feet or base need support, the strength of the frame, and a firm, level floor. Your dryer also needs a stable platform, even though it doesn’t shake in the same way as a spinning washer.

Fit matters as much as strength. A platform that is too small, too large, or shaped in a way that blocks the appliance’s feet can leave the machine poorly supported. It also must not block required access to hoses, cords, vents, or other parts you may need to reach. Follow the manuals for both machines, since their instructions can differ.

A raised machine can be harder to reach and may be less stable if its support is not designed for it. Don’t assume that a platform is safe just because it feels solid when you push on it by hand. The washer’s repeated movement puts different demands on the frame.

Plan the Size and Height Before You Build

  1. Read both manuals. Find the instructions for installation, leveling, and support. Look for any restriction on raising the machine or placing it on a platform. If the directions are unclear, contact the manufacturer before building.
  2. Measure each appliance. Measure the width and depth, including any parts that stick out. Check the machine’s feet or base so you know where the platform must provide support. Don’t guess from a nearby machine or a picture.
  3. Check the room. Measure the floor space and the route the machine will take to reach the platform. Allow room to open doors, reach shutoff valves, and access hoses and plugs as the manuals require. Make sure the raised machine won’t hit a shelf, counter, or ceiling.
  4. Choose the height carefully. A higher washer can make loading easier, but it also raises the center of the machine and can increase the consequences of wobbling. Check that you can still reach controls and safely lift laundry in and out. Don’t choose a height that makes the machine awkward to use.
  5. Plan for the load. Use the machine’s listed weight and support instructions, not a guess based on how heavy it feels. The platform must carry the appliance and cope with movement during use. If you can’t confirm what the frame needs to support, pause and get advice before building.

Measure the washer and dryer separately. They may look similar but have different feet, shapes, or installation needs. A shared design should not force either machine to sit on an edge or leave a support point hanging over open space.

Build a Rigid, Level Base

Use materials and joints that can hold the required load without bending or loosening. The right material and frame design depend on the machines, their support points, and the manuals. No single board size or layout is right for every washer and dryer, so don’t copy a plan unless it matches your appliances and space.

  • Make the top fully supportive. The machine’s feet or base should rest securely where the manual says they should. Avoid a narrow ledge, a loose panel, or a top that can flex when weight is placed on it.
  • Prevent sway. Add firm supports that keep the frame from leaning from side to side or front to back. A frame that looks strong from the front can still twist if its sides and corners are not held together securely.
  • Secure every joint. Fasten the frame parts so they cannot slide or separate. Check that the fasteners do not stick up where they could catch the appliance or leave it sitting unevenly.
  • Keep the base flat and stable. The finished platform should sit firmly on the floor, with no rocking corner. Don’t use loose scraps or soft material under a leg to compensate for a floor that slopes.
  • Leave needed access clear. Keep the route for hoses, cords, and any other parts shown in the manual open. Don’t pinch a hose between the platform and the wall or make a shutoff valve impossible to reach.

Before moving a machine onto the platform, press down on each corner and check for rocking, bending, or a joint that shifts. Look closely at the corners and the points where the top meets the frame. If anything moves, creaks, or feels loose, revise the base before it carries an appliance.

Position and Level the Machines

  1. Set the platform in its final place. Put it on the intended floor, not on a temporary surface. Check that it sits flat and does not rock before you add a machine.
  2. Move the appliance with help. Washers and dryers are heavy and awkward to lift. Don’t try to raise or balance one alone. If you can’t move it without losing control, ask a qualified mover or installer.
  3. Center the machine on its support. Place it so every foot or required support point sits fully on the platform. Check from the front and sides. The machine should not overhang or sit partly on an unsupported edge.
  4. Adjust the machine’s leveling legs as directed. The leveling legs are the adjustable feet under the appliance. Follow the manual to make the machine even from side to side and front to back, then secure the legs if the instructions call for it.
  5. Check the connections and clearance. Confirm that hoses are not kinked or stretched and that cords are not trapped. Make sure the machine can be reached for shutoff or service as required by the manual.
  6. Watch the machine during normal operation. Stay nearby when the washer first spins. Look for the platform shifting, the machine walking, or any corner lifting. Stop the cycle if you see movement, hear a new knock, or notice the frame changing position.

A washer that walks across its platform is not fixed by pushing it back into place. Stop using it until you find the cause. The machine may be uneven, the floor or platform may be moving, or the load may be making the washer shake. Check the manual’s guidance and correct the support problem before running another load.

One bulky item can bunch up on one side of the basket and cause shaking. If the platform itself stays still and the machine’s manual points to an uneven load, redistribute the laundry as directed. But repeated movement, even with an ordinary load, means you should stop and inspect the machine and platform.

Warning Signs: Stop and Rework the Setup

  • The platform rocks, bends, twists, or shifts when you press on it.
  • A washer or dryer foot sits partly off the top, or the machine overhangs the support.
  • The machine moves during a spin, or a corner lifts from the platform.
  • A joint loosens, a fastener pulls free, or the frame makes new cracking or popping sounds.
  • Hoses, cords, shutoff valves, or required access points are blocked or strained.
  • You cannot confirm the platform’s load support or whether the appliance manual allows this setup.

Stop the washer or dryer if the frame shifts or the machine begins to walk. Don’t try to steady a moving appliance by hand. If you cannot safely lower the machine, or you see damage to the floor, wiring, or water connections, keep clear and get qualified help.

Ask an installer, carpenter, or other qualified professional to review the design if you are unsure how to support the machine or brace the frame. Contact the appliance manufacturer about manual restrictions or required support. A professional can also help if the floor is uneven or seems unable to carry the raised machines securely.

Homemade Platform or Purpose-Built Pedestal?

A homemade platform gives you control over its shape and height, which may help when you are working around a tight space or want storage underneath. That flexibility also means you are responsible for getting the fit, strength, and stability right. If one of those details is uncertain, a custom build is not the safer choice.

A purpose-built pedestal may be designed for a particular appliance family or type of installation. That does not make every stand suitable for every machine. Confirm the exact fit and support instructions on the appliance and stand information, and follow the manufacturers’ guidance.

Choose a ready-made support if the manual calls for a compatible pedestal, if you can’t confidently build a rigid frame, or if the machine won’t sit securely on your design. Don’t buy or build based on a “universal” label alone. Check the actual dimensions, required attachment or placement, and any model limits before putting a machine on the stand.

If the manuals allow a raised platform and you can build one that fully supports both machines without wobble, a homemade option may work. If you cannot verify those conditions, use a support that the manufacturer says is compatible or ask a qualified professional to assess the setup.

FAQs

Can I use the same homemade platform for my washer and dryer?

Only if the platform gives each machine the support it needs and fits both sets of feet or bases. Measure them separately and check both manuals. A platform that fits one appliance may leave the other poorly supported.

What material should I use for a washer pedestal?

There is no one material or frame size that suits every machine. The choice depends on the appliance’s weight, support points, and the design’s ability to resist bending and sway. If you cannot confirm the materials and joints can carry the load, get help before building.

How can I tell if the washer is level on the platform?

Follow the washer manual’s leveling instructions and check that it is even from side to side and front to back. Confirm that the platform itself sits flat and that every appliance foot is supported. If the washer still moves during a spin, stop and inspect the setup.

Should I keep using the washer if the platform wobbles?

No. Stop the cycle if the platform rocks or shifts, and don’t run another load until the cause is corrected. If you can’t safely move the machine or repair the support, ask a qualified professional for help.

Related guides: best luxury front load washer and dryer sets with pedestals.

4
1 ratings
Joanne Neal
WRITTEN BY
Joanne Neal
Joanne Neal, based in Miami, is a leading female expert in home appliances. Specializing in energy efficiency, she has 10 years of experience and a Master's degree in Environmental Science from the University of Florida.